Question about HP PhotoSmart 7550 InkJet Printer

1 Answer

WONT PRINT CALIBRATION PAGE

Put in new cartridges and now wont print the calibration page

Posted by on

  • Machelle Turner Jan 06, 2009

    Thanks I will give it a try.

  • Machelle Turner Jan 06, 2009

    Thanks this did the trick.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 237 Answers

Take out the cartridges and turn off the printer. Turn it back on, and THEN put the ink cartridges in. After that, try to print the calibration page.

If this does not work, clean your printer using the cleaning maintenance from your HP printer software

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My kodak esp 5210 will not print a test page or a document from my computer.


Hello,
You will only get the calibration page no matter what you try because the printer needs to complete that task before it will let anything else get printed. This cannot be avoided for this model printer! Just follow the instructions as listed on the calibration page (even though you think it may not be needed) and then the printer will act normally!
Good Luck!
Rich Lilja.

Feb 27, 2015 | Kodak Esp 5210 All-in-one Inkjet Printer

1 Answer

I need to calibrate my hp deskjet 3845 but when I click the button to calibrate it says it's lost communication with the device


Hello

Calibration is one of the functions performed from the Printer Assistant icon on the desktop. If the Printer Assistant icon on the desktop has been deleted from the system, the same tasks can also be accomplished from the Printer Toolbox . The Printer Toolbox can be accessed through the Printer Folder or by right-clicking the Printer Icon on the Taskbar

Please follow these steps to calibrate your printer

Double-click the Printer Assistant icon on the desktop. The Printer Assistant menu will appear with a list of options

Select the Tools and Updates option or the Utilities option (depending on your driver version).

Printer Maintenance menu will appear.

Select the Calibrate Printer tab from the Printer Maintenance options

Click the Calibrate tab. The printer will print the first calibration page.

In the Cartridge alignment page, please inspect the straight colored lines in Sections A, B, C and D . Choose the straightest lines in each section to indicate the best cartridge alignment.

In the Page alignment area, please verify Section E . Then, select the bar and the arrow closest to the edge of the page without being cut off, to indicate the best page alignment.

In the Calibrate Device window, enter the selected alignment values in the Pen Alignment and in the Page Alignment fields and click the Continue tab

The second calibration page will be printed now. The page will contain two patterns: a square and a cross . The lines on the patterns should be horizontally and vertically aligned . Click the Done tab if the lines are correct or the Calibrate tab to repeat the calibration process

The first calibration page contains five sets of alignment patterns. The calibration will cover two areas of alignment. The Cartridge alignment is designed to obtain the best print quality and the Page alignment is designed to ensure that the print is aligned correctly on the page.



If the Printer Assistant and its files have been deleted from the system, the maintenance features in the Tools and Updates section of the Printer Assistant are also available in the Printer Toolbox .
Open the Printer Toolbox and perform the services by following the instructions below:

Right-click the Printer Icon on the Taskbar .

Click Open the Deskjet Toolbox option.

Select the Printing Service tab in the Printer Toolbox .

Choose the Calibrate the printer option.

NOTE:HP recommends to use HP plain paper when performing the cartridges calibration process.

NOTE:These printers could work with one or two print cartridges. HP recommends to perform the cartridge calibration process with the two cartridges installed in order to get the best print quality. Anyway, the printer can also be calibrated with one cartridge installed if the customer decides to work in that way.

Jan 16, 2011 | HP Deskjet 3845 InkJet Printer

1 Answer

Whenever I print color, entire page comes out blue. I have replaced the cyan cartridge (twice) and the Laser Transfer Kit. Sometimes there are thick blue streaks in addition to the overall blue color. What...


Run the "disable cartridge check"
It will be in the Diagnostics.
Once you start the test, you can remove all the cartridges. Put the cyan in the black cartridge slot.
print a config page. If it is all blue, you have another bad cartridge. If it prints correctly(minus the other colors)...continue
Now put the magenta in the cyan cartridge slot. Print the config page again. If you have red all over the page, you have a problem with the slot itself.
Press the STOP button and then select EXIT diagnostics. Put the cartridges back where they all go and run CALIBRATION more than once.
Select/menus/down arrow/configure devce/select configure device
Down arrow/print quality/seect print quality
Down arrow/ calibrate now. Select it and wait.

Oct 25, 2010 | HP Color Laserjet 3550 Printer

1 Answer

Printer not printing photos with all colors


  1. Lift the printer access door, then remove the ink cartridges from the printhead.
  2. Verify that the label on the ink cartridges is intact, and that the cartridges are not damaged.
  3. Verify that the KODAK Ink Cartridges have not been refilled.
  4. Insert the ink cartridges into the printhead, then press down firmly until you hear them click into position.
  5. Close the printer access door.
  6. Check the printer status monitor on your computer (or the LCD screen on the printer) to determine if there is sufficient ink available for your print job.
  7. NOTE: Once the "Black ink cartridge is low" or "Color ink cartridge is low" message is displayed, print quality can be affected.
  8. Reprint the picture or document that had the quality problem
If still same quality then...
  1. Load inkjet paper into the paper tray.
  2. On the control panel, press Menu.
  3. Select Calibrate Printer.
  4. Select Print Calibration Page
  5. Press Start.
  6. When the print is complete, press Cancel to end the calibration process.
  7. Check the six color bars on the printed calibration sheet.
  8. 5000calsheet_color_bars.jpg
Are the color bars completely filled with solid color?


If no then:

  1. Press Menu.
  2. Select Clean Printhead, then press OK.
  3. Select Deep Clean, then press OK. The On/Off light flashes green during the cleaning procedure.
  4. When the On/Off light glows steady, press OK.
  5. Select Calibrate Printer.
  6. Select Print Calibration Page
  7. Press Start.
  8. When the print is complete, press Cancel to end the calibration process.
  9. When the print is complete, press Cancel to end the calibration process.
  10. Check the six color bars on the printed calibration sheet.
  11. 5000calsheet_color_bars.jpg
Are the color bars completely filled with solid color?

If again No...

then printhead needs replacement... call Technical Support to get it replaced




May 25, 2010 | Kodak EASYSHARE 5300 All-In-One InkJet...

2 Answers

Thinking of cleaning the print head? ?


Try this one, Turn on the printer, Take out the inks, remove the printhead, put back the printhead make sure it will snap and you hear a click, put the inks back, wait for the printer to initialize, Press the Menu button, look for Calibrate printer, then print calibration page, then scan it after. Load a regular paper. Then try to print a demo page by pressing Photo and Copy at the same for 5 seconds then let it go. If same problem persist call this no for further assistance 1800 421 6699
Thanks

Aug 27, 2009 | Kodak EASYSHARE 5100 All-In-One Printer

1 Answer

Prints set-up page every time printer is turned on after changing print cartridge


That is probably the calibration page (if that´s the case, it is always necessary when a new cartridge is installed). If the equipment is an All-in-One printer, put that page in the scanner and press the Scan button.

Aug 19, 2009 | HP Printers & Copiers

1 Answer

Hp designjet 30n will not print


replace both ink cartridges with NEW GENUINE HP ink carts.

Jan 27, 2009 | HP DesignJet 30n InkJet Photo Printer

1 Answer

The printout has lines going through the pictures or wordings


here is the troubleshooting steps
try to remove the ink cartridges and put it baack again but make sure to hear a click sound when you put the ink cartridges,after that try to print again picture and if still has lines through it press the menu in the printer scroll down until you can see the calibrate printer,press ok and select the print calibration page and hit the ok button..after it print place the calibration page in the scanner glass and press start, try to print again a picture and if still has a line call the kodak hot line 1 800 421 6699 and you might have a printhead replacement.

Nov 15, 2008 | Kodak EASYSHARE 5500 All-In-One InkJet...

2 Answers

NO CALIBRATION SHEET


Hello, you can print a calibration sheet from the front panel of the printer. Hit menu on the panel of the printer and scroll down to calibration printer and hit ok. Then hit ok on print calibration page and it should proceed to print a calibration page. After it is done printing, it will tell you to scan the calibration sheet.

Feb 10, 2008 | Kodak EASYSHARE 5500 All-In-One InkJet...

Not finding what you are looking for?
HP PhotoSmart 7550 InkJet Printer Logo

Related Topics:

649 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96333 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...