Question about Computers & Internet

1 Answer

We are using IBMx3650 server,it getting restart again and showing that BIOS not installed

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,692 Answers

Flash the BIOS or Buy a new BIOS chip and install it. 

Posted on Jan 06, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

IBMx3650 amber light appears , error indicates CPU

Most probably this would be Motherboard issue. Rare cases for processor fault. Easy to find out if server works on dual processor

Trouble shooting:
1: Perform Power Cycle (Turn off server, remove power cord from server and wait 15 min)
2: Try with minimum configuration (1 cpu, 2 ram )
(swap CPU if have dual)
3: Perform IMM update

If issue remains, replace motherboard and see if it solves issue.

Oct 21, 2013 | IBM x3650 Server

1 Answer

Install linux

Did you save it to cmos before restarting your computer ? F10

Restart your computer

During the boot process you will see on the screen to press a certain key to enter setup usually the Delete or the F2 key

Press and hold that key during the boot up process to enter BIOS the using arrow key scroll down to advanced bios features press enter change your first boot device to cd,press escape then press f10 to save to cmos to restart

note this will erase you operating system you will have to have an operating system disk to load it onto you hard drive or create a partition to load another operating system

(note after you have loaded the operating system you should go back and change the first boot device to your failsafe or optimized defaults)
after windows has loaded

your computer will automatically restart it might restart 2 times one to finish the installation
the next will be because the operating system is loaded and will boot from your cd

during the boot process you will see on the screen to press a certain key to enter setup
Press and hold that key during the boot up process to enter BIOS using the arrow keys load

failsafe defaults or load optimized defaults press escape then press f10 to save to cmos to restart
otherwise it will keep booting from the cd /dvd drive

hope this helps

Oct 26, 2012 | Intel Dell Poweredge 860 Server 1-socket...

1 Answer

My server cant boot after a fresh intall

Reshuffling disks will disturb the Logical drive .Recreate RAID Install OS , Set the Boot controller order in system bios Pressing F10key

Jul 25, 2012 | HP Compaq ProLiant ML350 G3 Server

1 Answer

Netfinity 5600

It is certainly not ok for it to take so long to show bios.

This usually means there is a hardware conflict at low level (not a broken part)

This can occur if there is more than one disk that it has to look at that it cannot work out (this may be in your case)
you may want to start the system with only one disk in and get i runing from there before adding extra storage.

May also be of help to may

You did not say which OS you were intending to install but thee is plenty of documentation for that around

If this information was useful please click

Aug 14, 2009 | IBM Netfinity 5600 8664 Server

1 Answer

Raid not showing

The Raid's not showing from the startup? You may be infected. Viruses tend to infect one drive only but this tends to break the Raid. Most non-Raid anti-virus software won't do a good job at cleaning both (or more) drives. Check your BIOS to make sure the Raid is turned on. Then run a good Raid anti-virus program.

Mar 29, 2009 | HP Compaq ProLiant ML350 G3 Server

1 Answer



this is not a sufficient to answer. but, you can get some idea in the following information:

if you have a plan to install AD:
  • install AD using manage your server wizard. (or)
  • install AD using DCPROMO command
After, you have to follow the AD installation instructions to store the ntds and sysvol files.

installing dns, is also need for a domain to adding clients.

after this, you can get your desired domain controller and active director users and computers information.

i think, this may be useful for you.


Feb 12, 2009 | Microsoft Windows Server Standard 2003 for...

1 Answer

PowerEdge Server won't boot after memory upgrade

if you really need the BIOS update. you need a working PC to download the BIOS and unzip it to a CD. install it, since the PC do see the CD, you may have do some maneuver to ge the BIOS installed.

Oct 29, 2008 | Dell PowerEdge 1800 Server

2 Answers

Can't get Netgear PS121v2 to work on my laptop

I finally figured it out myself. The problem is that when you uninstall the print server software, it does not do it correctly. I used regedit to manually remove the server software and reinstalled, and all is well. Hope this helps.

Apr 02, 2008 | NetGear PS121 Print Server

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides