Question about Sanyo PLC XU30 Multimedia Projector

1 Answer

Projectors i have a canyo plc-xu70 which i brought secondhand. when i got it home i pluged it in and it powerd up fine but after i turned it off it won,t turn on anymore not even the standby light comes on. does anyone have any suggestions i would be very gratefull thanx.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 563 Answers
Re: projectors

HI there

Check that your power cable is ok. Best way is by trying a differnt cable. If the problem still shows , you might have to open it up check if the fuse on the powersupply board is ok and then worst case cenario have the powersupply replaced.

Hope this is of help !

Posted on Mar 27, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have an Sanyo PLC-SU07E Multimedia projector. I

1,Turn the projector on,press the Menu botton
2,Press the Left ,Right,Up or Down to find the "lamp usage" and the reset option.
3,select "Lamp replacement counter Reset ?"
4,select "Yes"

Jerry China
Tel: +86 131788 67858

Aug 09, 2013 | Sanyo PLC SW20A Multimedia Projector

1 Answer

Sanyo plc xu115 new bulb wont fire. power light turns green at first but after a few seconds it turns flashing red. the old bulb exploded on this projector.

Could be a burnt capacitor on the circuit board. Replace capacitor if you can determine which one it is. There are only a few.

Apr 20, 2011 | Sanyo PLC-XU115 Projector

1 Answer

Hello.... Sanyo PLC-SU20N projector....shuts down within 3 seconds of turning on.

If the lamp doesn't strik, it will.
Check the ballast unit and lamp age.

Mar 19, 2011 | Sanyo PLC SU20N Multimedia Projector

1 Answer

Hi I have a Sanyo PLC-XP18 projector and it has recently developed a problem. I was watching a film the other night and the projector just cut out. Now when i try and turn the projector on the the fans...

READY light is green when the projector is ready to be switched on
LAMP is dim when the projector is ON, but goes bright when it reverts to STANDBY.

Check that the lamp cover is fully down and the cover switch is activated

Feb 28, 2011 | Sanyo PLC XP18 Multimedia Projector

1 Answer

How do I change the input from the DVI-I input to the 15

I found the online manual and followed the instructions to set to "auto" input. Everything works fine.
It had been a discouraging ordeal trying to locate a new DVI cable (which came with the projector)
and as it turns out the 15 pin cable works fine. Thank you.

Jun 11, 2009 | Sanyo PLC XU50 Multimedia Projector

1 Answer

Sanyo plc sw30 help

i had a sanyo plc sw30 wich had the same problem and it turned out to be the bulb replaced it with new one and this seemed to solve the problem. Theres a few places to get new ones but they are not cheap looking at between £150 to £180 hope this helps

Nov 02, 2008 | Sanyo PLC-SW30 Multimedia Projector

1 Answer

Temp warning

Clear the air flow and replace or clean air filters. that will solve.

Nov 02, 2008 | Sanyo PLC XF45 Multimedia Projector

Not finding what you are looking for?
Sanyo PLC XU30 Multimedia Projector Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sanyo Multimedia Projectors Experts


Level 3 Expert

2236 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

66518 Answers

Are you a Sanyo Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides