Question about Office Equipment & Supplies

2 Answers

Software to istall Hp laserjet 4L c 2003

I am trying install this printer for my mother who has had stroke and it seems to be the only printer that she can remember how to run it I am not finding the software to install it. In the manual on page 3-3 it says setup disk into the floppy disk drive. I know tha she does not have a floppy but can I get on a web site when I have her laptop and down load from a web site right into he laptop.

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi Dear

I am Imtiyaz Here

Do one thing my dear First Cd Drive in the cd Bores the cd one icon is a is there setup file run it

Posted on Jan 06, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,692 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have upgraded my OS from Vista to Windows 7 home and am having the following installation issues. During the last phase of installation, with a full driver download package from the HP web site, when...

Within the HP software, is a "tool box" in the tool box, there is a filel called "Scrubber" run this, (it will seem as if nothing happened) then try re installing the software. Remember , leave it disconnected until you are advised to plug it in.

Dec 29, 2010 | HP Office Equipment & Supplies

1 Answer

Epson Status Monitor 3 says "Printer is not ready" while everything seems to function ok

Remove printer, uninstall software and then reinstall the software in the PC. Now connect back the printer and get the new harware detected to be installed.
The printer must function well or else there is a fault in the mother baord of the printer.
Try to use maintenance to clean head.Open properites of printer to check on ink properties if low replace ink and reset as before.

Aug 30, 2010 | Epson STYLUS CX3900 All-In-One InkJet...

1 Answer

I can not print. An "E" displays where the number of copies should be.

It seems that the issue is with the driver of your computer and it is not letting you print. You can therefore download new upgraded set of drivers from
Once downloaded, try to run the downloaded program and uninstall your printer using it and restart your computer. Now run the downloaded software once again and install your printer. It will now work fine. Remember do not uninstall Printer's driver from Add/Remove Programs (Winodws XP) or Programs and Features (Windows Vista and Windows 7).
Enjoy printing once again.

Mar 27, 2010 | HP PSC 1210 All-In-One InkJet Printer

1 Answer

I have never instaled a distributer before and i would like advice. i have a 1990 chevy s-10 blazer 4.3 liter auto trans

first set motor to top dead center cyl 1 thei insert distrib to first plug point remember it is rare you wont need to ajust distrib just make sure you are tdc and not on an intake or exhaust stroke as every cylinder has 3 strokes
1 intake
2 compression and fire
3 exhause

so make sure you are on compression stroke cyl 1
insert distrib to first cyl point and snug it down just remember you will likely have to ajust it

Jan 17, 2010 | 1991 Chevrolet S-10 Blazer

1 Answer

I donot know how to put ink in my printer jnhb55564

first turn on you printer.

second open you cover then you will see the print head cartridge is running out i think he will stop in you left hand side or right hand side.wait for he stop running.

third after stop running plug out ink just press down ink about 45 degree then you can take out ink.remember when you put out ink see number ink before installation.

4.when install ink remember to take out plastic sticker gum inside install ink jus put in inside by 45 degree the press up him after that is ok

5.close the cover and try to print.i think black ink in left and colour in right i no sure but try .... ok....

Aug 16, 2009 | Canon PIXMA MP150 All-In-One InkJet...

1 Answer

Hp photosmart c4280 all in one needs disk install & I don't remember when to plug in cords

You do not connect the USB cable until you run the software and it prompts you to connect it.

Here is a link to the setup guide in pdf format:

C4280 Setup guide

Oct 27, 2008 | HP Photosmart C4280 Aio Printer

1 Answer

Canon mp-730 print head does not move

it seems you open or unscrew the printer.
this may happen if the mother board has no nigative pole.
you have to reset the mother borad.
cannot do that from the available options
the reseting procedure is to take the motherboard out and you have to shortcut the battary for 10 seconds.
re install it , and try it

Feb 18, 2008 | Canon MultiPASS MP730 All-In-One InkJet...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts


Level 3 Expert

8068 Answers


Level 3 Expert

2237 Answers


Level 3 Expert

79865 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides