Question about SanDisk Sansa e200 MP3 Player

3 Answers

Rebooting sansa e200

I was just wondering if anyone knows how to completly reboot/restart a sansa sandisk e200 like completly start it over again because mine is like totally messed up i have like 7 problems

Posted by on

  • Anonymous Nov 14, 2008

    mine

  • Anonymous May 16, 2009

    when i turn it on it say battery too low system shutdown

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Press the hold button the press the record button for like 5-8 sec.

Posted on Jun 26, 2007

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Get a small phillips head screw driver or a pocket knife, open the back take out the battery, put it back in

Posted on Jun 04, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

PUT IT ON THE CHARGER

Posted on Dec 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sansa e200 2gb is countinously restarting


OK TRY THIS...Turn unit on and allow to completely run dead.Allow to fully charge.this should reset and no more constant reboot.Please allow to fully charge.Do not rush this process.RICHARDM69

Jan 07, 2009 | SanDisk Sansa e200 MP3 Player

1 Answer

SANSA E200 NOT SHOWING THE MENU SCREEN


Try to format the SANSA E200.


You can do this by simply holding down the Power/Menu button for about 15 seconds. After the reset, any changes you have made to the e200 during its last use will be lost.

PLEASE RESET USING THE RESET PIN PRESENT IN THE SIDE.
AND FORMAT THE PLAYER . if this dosen't work your player is faulty

Nov 21, 2008 | Computers & Internet

1 Answer

Sansa Media Disc freeze/restart


You can try to reset the device by pressing the power button for about 15 to 20 seconds..if that doesnt work I would recommend you to go to the sandisk site to update the firmware on your device or you can contact sandisk to they can help you with updating the firmware on your device..Please follow the link below to get the firmware
http://www.sandisk.com/Retail/Default.aspx?CatID=1376

The number for sandisk is 1-866-726-3475
Please rate accordingly
Thank you
Computerrep

Aug 22, 2008 | SanDisk Sansa e200 MP3 Player

1 Answer

Rebooting and rebooting and rebooting


Hardware issue then - this player must be replaced. Make sure you have tried all of these methods first:
These are the most common methods for recovering Sandisk's Sansa Mp3 Players. I have been almost universally successful in recovering Sansa players using one or a combination of these methods. These methods do not work if you are having synchronization or music format issues - they are for recovering a player that will not power up, freezes, flashes, is not recognized by the computer, and a host of other issues.

Reset the Sansa Player first. On most models, restart is done by holding the power button in for 15 seconds or longer. Check your specific manual to be sure. The manuals are available from the Sansa website if they have been misplaced.
Download the Sansa Recovery Tool from the Sansa website.
Format - Erases Everything: Connect your Sansa player to the computer and open Windows Media Player. Click on the Sync tab. Pull down the drop down menu underneath the Sync tab by moving your cursor over the Sync tab and left clicking on the little black arrow underneath the Sync tab. Highlight "Sansa 1GB" (wording may vary slightly), and then select "Format." - this should erase everything.
Firmware Upgrade- Erases Everything: Get the latest firmware upgrade from Sansa - it updates the firmware and erases every song in the player all at once. Note: this method doesn't work if already have the latest firmware. Go to this website and click "Firmware Updater" to find out: http://www.sandisk.com/DriverDownload/driverList.asp
If these fail, then:
Try this: disconnect the player from the computer, turn it off, hold in the volume + button, and reconnect the player to the computer while holding the volume + button in. Keep holding the volume + button for an additional 5-50 seconds. Windows should eventually go into recovery mode and revive the player- it will pop up a window that says Found New Hardware Wizard.
If you get the problem where MTP Device keeps popping up continuously, uninstall the “MTP Device” by going to Start à Control Panel àSystem à Hardware à Device Manager (you computer may vary slightly, depending on Windows Version).
You may have to restart your computer after each of these methods to get them to work properly. Disconnect your Sansa player BEFORE shutting down your computer.
-Tha Mp3 Doctor

May 30, 2008 | SanDisk Sansa e260 MP3 Player

1 Answer

Sansa e200 mp3 player


you hae a croupt file
erase disk completly and reinstall your music
this appen to me all the time whn i get a bad song down load
let m know if you need any more help with this
richard from chicago

Apr 05, 2008 | SanDisk Sansa e200 MP3 Player

1 Answer

Sansa e200 6MB does not start correctly


1-866-726-3475 Sandisk Customer Support

www.sandisk.com

click on support at the top; click on MP3 players,
find your Sansa and click on it there’s a lot of info

Mar 26, 2008 | SanDisk Sansa e200 MP3 Player

1 Answer

Restart


you could have downloaded a bug, your motherboard could be damaged. you are going to have to get a new one, but with what you paid for the sansa, it may not be worth it. thank you, connie

Jun 25, 2007 | SanDisk Sansa e250 MP3 Player

1 Answer

Sansa e200


I would try formatting the drive/player. Why can't you delete the bad file?

Jun 19, 2007 | SanDisk Sansa e200 MP3 Player

7 Answers

It wont turn on


I would like to offer this solution, but this solution is only meant for the "Standard" E200 players (there are 2 types of E200 players -- the Standard E200 and the "Rhapsody" players, indicated with an "r" after the E200 such as "E260r". I'm hoping you have the standard E260. Switch your Sansa E260 to its Recovery Mode: 1. Make sure the player is powered off 2. Enable the "Hold" switch (located on the top of the player). You would know it's enabled when you see the "orange-colored" surface 3. Press the "Record" button. Make sure you keep it pressed while pressing on the "Menu" button. 4. keep your fingers pressed on these 2 buttons until the E260 LCD screen displays "Welcome to Recovery Mode" 5. Connect your E260 to your computer. (Just a reminder: The minimum Operating System requirements for a Sansa E200 player is Windows XP and above) 6. Double-click on "My Computer" and you would see your Sansa E260 appear as a "16 MB" drive. Note: If you do not see that "16 MB" drive/partition, please repeat steps 1-6. Next, Apply the firmware for the E260 (your player should be connected to your PC at this time): Step 1: Use this link to download the firmware for your Sansa E260 (for better results, please save this file on your "Desktop": http://www.sandisk.com/Assets/File/Downloads/firmware/e200fw01.00.12.exe Step 2: Double left-click on the downloaded file, and follow the on-screen prompts. The file will automatically re-flash your player and format it as well, thereby clearing all possible file/system corruptions that may have occurred which caused the "Load Main Image Failed" notification in the first place. Step 3: When the process is complete, unplug your E260 from your computer, and please make sure you disable the "Hold" switch Step 4: Power up your E260 and 90-99% of the time, it would boot up successfully. Step 5: Enjoy using your Sansa E260, just like I do. (I love this player)

Apr 20, 2007 | SanDisk Sansa e260 MP3 Player

Not finding what you are looking for?
SanDisk Sansa e200 MP3 Player Logo

Related Topics:

587 people viewed this question

Ask a Question

Usually answered in minutes!

Top SanDisk Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gyula Lacz

Level 3 Expert

486 Answers

Mohamed Ismail
Mohamed Ismail

Level 3 Expert

462 Answers

Are you a SanDisk Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...