Question about NetGear WGR614 Wireless Router

1 Answer

Angel all my lights of my wierless router are all on

Posted by on

  • mooseblaster May 11, 2010

    First up, what were you doing before these lights came on? Was it just everyday use, were you updating the firmware, etc.? Secondly, have you tried a 'hard reset' of the router? This involves getting a pen (or other small object) and pressing the small reset button which is next to the antenna down for 30 seconds. Then unplugging for 10 seconds. Hope it helps!


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 232 Answers

In this case,we can do a power cycle of the router.steps to do a power cycle
1.unplug the router power adapter and then the modem power adapter if its a cable modem then we should also unscrew the coaxial cable wait for 10 sec and then screw it and now plug the modems adapter first wait fir lights to be stable and then the routers power check the lights.
If power cycle doesnt resolve your issue then do a reset.restting a router is setting it to the factory setting so pls note the changes you have done in the netgear smart wizard page if any.
1.HARD RESET-you ll find a circular hole(reset button) at back panel of the router(see d chart on the router ).take a paper clip and press and hold for 30 secs and release it after 30 secs.
2.FUNNY RESET-If the previous step doesnt work,then we have do the funny reset.Here press and hold the reset button for 1 minute simultaneously plug and unplug the router 3 times.
Hope these steps solve your problem if not reply me and if this issue is solved pls rate me to improve my service.

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wierless router not responding

There are a few things thatcan cause you to lose wireless connection with your wireless router.1. Weak signal strength,check the signal strength on your wireless card. If it is weak move thewireless router away from brick or concrete walls and if possible locatethe wireless router higher up.2. Have you secured yourwireless router from people near your from unauthorized access? i.e. change thedefault password, setup encryption use WPA2 or WPA, change the default SSID,and turn off SSID broadcast, and for added protection, enable MAC addressfiltering which allows only the MAC address/es of your wireless card/s toconnect to your wireless router.3. You could be gettinginterference from electrical sources such as air conditioners, arc welders,washing machines etc. If so, the power supply to the wireless routers andcomputers etc should be connected to a surge protection power board, betterstill connect your computer equipment to an UPS (Uninterrupted PowerSupply). 4. Check the channels ofthe wireless routers and access points in your area and change the broadcastchannel on your wireless router to an unused channel or one that is currentlyused but has the weakest signal strength. This will minimize interferencewith your wireless router from other wireless routers and accesspoints in your area.

Feb 12, 2012 | NetGear DGN1000 Wireless Router

1 Answer

Does not wierless work in xp computer and 2 ipad.

Are you using a laptop? If not, the computer that you are using should capable of connecting via wireless connection. And the Modem /router should be transmitting wireless signal. If you can successfully connect via wifi, then all of your wireless end devices should be connected via wi fi a as well. check your local network for issue isolation.

Dec 30, 2011 | 2wire (2701HG-B) Wireless Router

1 Answer

When connect to internet wierless says local only no internet

try to power off then power on and reconnect the connection of the router. if problem still exist try to call to your internet provider.there may be a shutdown system happen on them so why there you can'r receive an internet connection.

Feb 22, 2011 | Belkin Basic Wireless Router

1 Answer

Hiee I am using netgear N300 jwnr2000 router. The router worked fine for few days it has suddenly stooped working.Any of my wierless devices are not able to detect my router since the wifi in been...

Unplug both your DSL/Cable Modem, and the Router from power. Wait 30 seconds. Plug in power to DSL/Cable Modem only, and wait for it to connect. then plug in power to Router, and wait for it to start up. Give it about 1 min. If the lights are still not on, you may need to reconfigure your router. If this does not work, connect your cable/DSL modem to your computer directly, and power cycle it again. Once it is online, check to see if you can get online, if you cannot, contact your internet service provider, as you have ruled out a problem with the router.

Dec 28, 2010 | NetGear WNR2000 Wireless Router

1 Answer

What is the WEP key for Belkin Wierless Router f7d201


Step 1 : Connect Router - Computer ( Wired)

Step 2 : Open Router Setup by typing on the address bar of internet explorer

Step 3 : On the Left under wireless Click Security

Step 4 : If it asking for a password leave that blank and click submit

Step 5 : On this Page you can find the WPA Key ( If it is a bunch of dots then Uncheck "OBSCURE PSK ")

Dec 20, 2010 | Belkin Basic Wireless Router

1 Answer

N router/ The blue wierless light is not lit!? unable to connect to my other PC

Push and release the “Reset” button.
The lights on the Router will momentarily flash.
The “Power/Ready” light will begin to blink. When the “Power/Ready” light becomes solid again, the reset is complete

Follow me on Twitter

Jun 08, 2010 | Belkin (F5D8231-4) Wireless Router...

1 Answer

I am tring to hook up a linksys wierless router but it wont work

Hi Friend,
Please follow the below website,here you can find the Step by Step procedure for the Linksys Router Configuration

If you have any queries please feel free to contact us


Apr 13, 2010 | Routers

1 Answer

Have a Wierless-G router can not install, tried 3 times. While installing it has very limited range , pc is 4-5 feet away & couldnt pick it up. Any ideas ???

check the wireless settings of the router. try to change the channel of the wireless network.
SSID broadcast should be enabld on the router. It depends on the computer also.
If your router is old then upgrade the firmware of the router. firmware is the software of your router.
Click here for more information about the router

Mar 27, 2010 | Linksys Wireless-G Broadband Router

1 Answer

How to connect to a wierless network ?

hello you could try this turn the power off to the modem and take the ethernet lead out. at the back of the modem is a reset button press and hold for 30 seconds after that reconnect the ethernet lead and power and re set up again good luck


Jan 24, 2009 | Gateway Belkin 54g Wireless DSL/Cable...

Not finding what you are looking for?
NetGear WGR614 Wireless Router Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Routers Experts


Level 1 Expert

31 Answers


Level 1 Expert

36 Answers

Phillip Whisenant
Phillip Whisenant

Level 2 Expert

120 Answers

Are you a NetGear Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides