Question about Lakewood Oil-Filled Electric Radiator Heater

Open Question

Wiring schematic for lakewood 7096 - Lakewood Oil-Filled Electric Radiator Heater

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: lakewood 7096 heater

Some of the newer models have a thermal fuse which may be blown. It doesn't look like a normal fuse at all. It is similar to a transistor in looks and should have continuity from one end to the other. It will be tied in to the incoming power cord inside the heater, and may be covered with rubber coating within the wire. It will look different when you notice it. Sometimes its too far down inside where the heat causes it to blow prematurely. The purpose is to cut the power to the unit in case it overheats. You can get one at radio shack for less than a couple of bucks. The older models don't normally have one, but I would suggest you put one in it if that's the case.

Posted on Jan 01, 2008

Ad
  • 4 Answers

SOURCE: I need the switch for Lakewood 7096 oil heater

This might be the switch,

Defond DRH-2415 15A 125VAC Lighted Dual Heater Switch

Posted on Jan 14, 2009

  • 34 Answers

SOURCE: need new double switch

Visit this page for parts:
http://www.lakewoodeng.com/html/parts.html

Posted on Apr 18, 2009

  • 1 Answer

SOURCE: Lakewood 7096

i went all over town looking for a switch. finally found two lighted switches at grainger carling technology part no. 1A824. ground down the outsides glued both together jumped across top and bottom terminal with copper wire and it seems to work fine now.only time will tell. i hate our throw away society which the junk imported in from china seems to foster.

Posted on Oct 08, 2009

  • 832 Answers

SOURCE: Lakewood heater 7101 schematic

The power cord goes the switch terminal 1 and 3.
Terminal 2 must be the opposite of terminal 1, such that when switched on, 1 & 2 connects. Terminal 4 must be the opposite of terminal 3, such that 3 & 4 connects.
Under this setup, you may connect red to terminal 2
and black to terminal 4.
Be sure of the 1 & 2 pair, as well as the 3 & 4 pair.
then, connect the red and black wires.
Hope this will help you.



Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need switch and cord for lakewood portable oil heater mod 7096


I have two 7096 models that do not work. Willing to sell for parts.
Electrical cords on both heaters are in excellant condition. Not sure about the switches.

Jan 20, 2013 | Lakewood Heating & Cooling

2 Answers

My heater model 7096, The 2 wheels are broken, Can I buy new one to have them replaced?


Not from lakewood. they went out of business. I suggest a harware store ot E-bay for a used unit.

Mar 30, 2011 | Lakewood Oil-Filled Electric Radiator...

1 Answer

Lakewood 7096


buy a new one and you will save money.the oil is probably gone. and it wont start.

Jan 03, 2008 | Lakewood Oil-Filled Electric Radiator...

1 Answer

Lakewood 7096 heater


Some of the newer models have a thermal fuse which may be blown. It doesn't look like a normal fuse at all. It is similar to a transistor in looks and should have continuity from one end to the other. It will be tied in to the incoming power cord inside the heater, and may be covered with rubber coating within the wire. It will look different when you notice it. Sometimes its too far down inside where the heat causes it to blow prematurely. The purpose is to cut the power to the unit in case it overheats. You can get one at radio shack for less than a couple of bucks. The older models don't normally have one, but I would suggest you put one in it if that's the case.

Dec 16, 2007 | Lakewood Oil-Filled Electric Radiator...

1 Answer

Model 7096 heater


http://www.ul.com/media/newsrel/nr041405.html
Concerning Lakewood Model #7096
RECALL
May cause electric shock!

Nov 20, 2007 | Lakewood Oil-Filled Electric Radiator...

Not finding what you are looking for?
Lakewood Oil-Filled Electric Radiator Heater Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lakewood Heating & Cooling Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Mack Baxter

Level 3 Expert

383 Answers

Paul Carew

Level 3 Expert

2598 Answers

Are you a Lakewood Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...