Question about Lexmark Refurbished MARKNET X2000 SERIES PRINT SERVER(46D0000) (4034321) Print Server

Open Question

Light 1 is flashing on MARKNET X2000 SERIES PRINT SERVER

I can't print and light 1 is flashing

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to reset the print server D-Link DP-301P+. I forgot IP address which I was changed according to network settings.


There are two steps that we can suggest,

A)

1) Install the psadmin software if you have not already. If you have lost the psadmin software then search for it on the web.
2) Start the psadmin software and click "factory reset".
3) If the software demands a password, try "SYSxxxx", where xxxx stands for the last four digits of the MAC address located on the underside of your server. (Example: if your MAC address were "63 XE 29 44 F2 96", then your password would be SYSF296.)
4) Click yes to confirm the reset.

B)

On the back of the print server you will find a pin hole, insert a paper clip for 30 secs with the print server powered on. All lights will flash. Try to setup the server again.

Hope this helps.

Regards,
Shrey

Jun 01, 2011 | D-Link DP 301P (DP-301P) Print Server

1 Answer

Printer 4550 Should I leave the power on 24 hrs


You can do of course, but just remember that the life of any electronic device equates to the amount of time it is on, so by leaving it on you are reducing its lifespan (maybe by only a tiny bit) and wasting energy.
If components are left on for a long time then there is a chance that they start to heat up, and heat eventually means failure for circuitry.

Oct 29, 2010 | Lexmark MarkNet X (46D0030) Print Server

1 Answer

I cant talk to m print server


make sure the lan cable is properly connected and the ip address is correct and you are able to ping the ip of print server.

Hope this helps. Please rate my response.
Thanks.
Have a good day.

Feb 23, 2010 | Lexmark MarkNet X2011E Print Server

1 Answer

Does not print


***hi there,il be willing to help you on that. ****
the nozzles of the printer might be clogged by dried inks thats why when your printing, its feeding the paper, as if its printing but no inks on the paper. print a nozzle check to see which part or color have clogs, if there are gaps or breaks, do head cleaning untill no more gaps then try printing.
Running a Printer Check
1. Load a few sheets of plain paper in the sheet feeder. 2. Turn off the Epson Stylus NX100 Series. 3. Hold down the nx100_tx100_ug.1.96.1.jpg Stop button as you press the nx100_tx100_ug.1.96.2.jpg On button to turn the Epson Stylus NX100 Series back on. Hold down both buttons until the nx100_tx100_ug.1.96.3.jpg On light begins to flash, then release the buttons. 1. Load a few sheets of plain paper in the sheet feeder. 2. Turn off the Epson Stylus NX100 Series. 3. Hold down the nx100_tx100_ug.1.96.1.jpg Stop button as you press the nx100_tx100_ug.1.96.2.jpg On button to turn the Epson Stylus NX100 Series back on. Hold down both buttons until the nx100_tx100_ug.1.96.3.jpg On light begins to flash, then release the buttons. 1. Load a few sheets of plain paper in the sheet feeder. 2. Turn off the Epson Stylus NX100 Series. 3. Hold down the nx100_tx100_ug.1.96.1.jpg Stop button as you press the nx100_tx100_ug.1.96.2.jpg On button to turn the Epson Stylus NX100 Series back on. Hold down both buttons until the nx100_tx100_ug.1.96.3.jpg On light begins to flash, then release the buttons. 4. Check the nozzle check pattern that prints to see if there are gaps in the lines. nx100_tx100_ug.1.96.5.jpg 5. If there are no gaps, the print head is clean and you can continue printing. If there are gaps or the pattern is faint, clean the print head. If your printouts are unexpectedly light, or dots or lines are missing, you may need to clean the print head. This unclogs the nozzles so they can deliver ink properly. Print head cleaning uses ink, so clean it only if quality declines.
You can also clean the print head by holding down the stop button on the printer for three seconds. (This only works when the red ink light is off.) Run a nozzle check to confirm that the print head is clean.
Caution: When you don’t turn on your printer for a long time, print quality can decline, so turn it on and print a few pages at least once a month to maintain good print quality. ***if my troubleshooting steps are helpful, pls vote for me, i will appreciate it, so that I can be a part of fixya, thanks, Godbless****

Jan 10, 2010 | Epson Stylus NX100 InkJet Printer

1 Answer

Network card, Token Ring fitted, what card do I need for ethernet?


You will need to use Lexmark's MarkNet N7002e print server.
Check this link:
http://www.lexmark.com/lexmark/product/home/500/0,6970,204816596_653399458_253501940_en,00.html?tabId=7

Oct 16, 2009 | Lexmark Optra S 1255 Laser Printer

1 Answer

LexMArk Marknet 700Oe: Booting problem


hmmm...ok..you'll need to reinstall the server software, where those reside..

Jun 15, 2008 | Lexmark MarkNet N7000e (1 USB port) 10/100...

4 Answers

HP LaserJet 1018 & DP-G310


Does your network have a dedicated computer server and the printer is attached to this server or is the printer attached to a dedicated print server device?
OR
Does a computer on your network shares its printer with other computers on your network?
There is insufficient information on how you configured your printer setup for me to give you a proper answer to your problem.

Jun 10, 2008 | D-Link Air Plus DP-G310 (dpg-310) Print...

1 Answer

Old IP address


You can reset the MarkNet X2000 to factory defaults - which includes resetting the IP address to 0.0.0.0 like this:

1. Press and hold the Test button until all four lights stay lit simultaneously, then release the Test button.
2. When #3 and #4 lights light simultaneously, press and release #1 (the Menu button).
3. When #3 lights press and release #1 (the Menu button).
4. At this point the X2000 print server has been restored to the factory default settings and should have an IP address of 0.0.0.0.


-John

Feb 06, 2008 | Lexmark Refurbished MARKNET X2000 SERIES...

1 Answer

New pc


Hi Goon,

Can you please provide me with your printers Make and Model and also your Operating System.

-Daniel.

Nov 18, 2007 | Lexmark Refurbished MARKNET X2000 SERIES...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Computers & Internet Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

micky dee

Level 3 Expert

2658 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Lexmark Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...