Question about Air Conditioners

1 Answer

My central heater is not blowing hot air, I am having to turn the thermostat on and off. I have the thermostat to 70, and the heater will blow hot air and then it will just circulate the air in the house, therefore bringing the temperature down. I looked at the unit and noticed that when the thermocople (heating element) goes red, the gas valve makes clicking and the flames come and then go out very fast. I noticed lots of clicking in coming from the gas valve. help please

Posted by on

  • robertogvele Jan 13, 2009

    The solution you guys gave me was very helpful, the unit is working better. Thanks a lot vanni7 .

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 163 Answers

Hi!!! relax your flame sensor is bad change and you will be fine..If it turns off and on change your flame sensormy central heater is not - 4c9410b.jpg

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Carrier heating unit in my attic ,


zone controller might be stuck seek help from service co.

Mar 25, 2015 | Carrier Air Conditioners

1 Answer

Unless we set the thermostat very high, like 80 degrees, the heater will blow cold air. When the heat does blow, it will eventually stop blowing heat and the fan will continue to blow cold air.


Check and make sure the filter is clean. This sounds like a restriction in the system. If the unit has central cooling make sure ther indoor evaporator coil is clean at the furance.The unit may be cycling the burners on and off at the high heat limit , fan/limit control. You can also eliminate the thermostst from the furance. Turn power off at the furnace and disconnect the wiring from the thermostat. Jumper the red and white wire together. Turn the furnace back on. The furance should run in the heating mode. Try this and see if the problem is still there.

Jan 25, 2011 | Air Conditioners

2 Answers

What supply house sells haier air handlers in Atlanta ga


any 4 tonnes air handler will fit if you respect de gas for the unit if r22 than than r 22 air handler if r410 than r410 air handler you can put r410 air handler if r 22 not avalable but be sure that expension valve is compatible.

Dec 13, 2010 | Haier HC48C1VAR Central Air Conditioner

1 Answer

My immersion heater keeps tripping out and we have no hot water or central heating, blowing the fuse every time. could we need a powerflush ??


You have an electricl shortage in the system since it keeps tripping or blowing a fuse. Would suggest having system evaluated as soon as possible to prevent any further damage or injury. Good Luck on your repairs

Dave

Oct 20, 2009 | Carrier TSTATHCP Programmable Thermostat...

1 Answer

My central air fan isn't blowing. The thermostat


Check the master circuit breaker at the power panel? Should be 2 50 amp vreakers. Turn them off rgen back on.

Jun 08, 2009 | Ruud UBHC Air Conditioner

1 Answer

Bryant Legacy Line air conditioning not blowing cool air..


Your outdoor condenser is in heat mode. Check the wires on the thermostat. Sounds like a small wiring problem and nothing else. Good luck. Please keep me posted as to you progress.

Apr 27, 2009 | Bryant 462AJC021BA Air Conditioner

2 Answers

Central heating HVAC blows cold air -


is there a light or source of heat near t stat or low battery in tstat

Jan 04, 2009 | Intertherm P3RA-048K Air Conditioner

1 Answer

Central air conditioning system


Check the filter(s). Dirty filters is the primary cause for such failures. Secondly check the thermostat and make sure that it is not turned way too low. Anything above 70 is safe from causing freezing on the unit. If the unit is already frozen then turn the unit off until it is totally thawed and then retry.

Jun 30, 2008 | Air Conditioners

1 Answer

20 year old central a/c heater not working


Check your thermostat and mode selector setting, thermostat setting should be set at warmer and mode selector setting should be at low heat or hight this is applicable for manual unit.
If it is a remote control just set the remote to heat mode.

sample only
d8936d5.jpg

Jan 02, 2008 | GE Quiet-Aire Ductless Split System Air...

Not finding what you are looking for?
Air Conditioners Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Conditioners Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Bill Long

Level 3 Expert

577 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Are you an Air Conditioner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...