Question about Hitachi NR83A2S Framing Nailer, Full Head, Plastic Strip Collation

Open Question

How to install spring on hitachi 83a magazine

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1383 Answers

SOURCE: Reassembling the Hitachi NR 83A2 (S) magazine

The reason that you are having trouble re-assembling the ribbon spring is that you need three hands to complete the job. As you recall the nail pusher just slips into the front of the rails. The pusher has the spring and a pin to retain the spool in place. Install the spring with the bolt hole towards leaver and slip into the front of rails. Take a small paper clip and bend a small hook to catch the ribbon spring. Hook the springs bolt hole with the paper clip and hold the spring in the approximate position for bolt as you push the assembly into rails and use latch to hold. While holding spring with paperclip, insert bolt thru rails and spring into nosepiece. Just break off the paperclip at this point and you are almost done. Some nailers have a metal support clip that you would need to have in place on bolt before installing bolt thru spring. For a breakdown of the gun go to www.toolpartsdirect.com. The other bolt for rails has a support/guide for the safety foot. Good luck and email if you have questions.

Posted on Apr 12, 2009

  • 548 Answers

SOURCE: Hitachi 83a Leaking Air from the Trigger

yes my guns i rebuild once a year at least

Posted on Aug 21, 2009

  • 121 Answers

SOURCE: On the Hitachi NR83A2 nailer. Where does the end

Hi,
It goes thru the same hole as the magazine bolt on the nose. Sounds like yours is broken.

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hitachi 83a


Assuming you have an NR83A
The main reason the driver won't return is the Cylinder exhaust ring is missing, broken, or improperly installed.
Also check to make sure there is not a nail jammed in the nose inhibiting the driver from returning.
My recommendation is to install a Service Kit #18000 which includes the exhaust ring.

Apr 13, 2014 | Tools & Hardware - Others

2 Answers

My nt50ae2 brad nailer jams in the magazine. the feeder rides on top of the nails.


This happens. The follower jumps over the nails and the magazine binds.

Step 1. Remove nails, unplug hose.
Step 2. Remove the bolt at the bottom of the magazine with a 2.5mm hex key.
Step 3. Remove the magazine while holding the nail follower in place to the magazine cover.
Step 4. Carefully remove the nail follower and gently extend the yellow warning indicator and follower spring.
Step 6. Inspect the nail follower. There should be 3 indentations that are stamped into nail follower face. This is the culprit.
Step 7. With a small punch, make these three indentations deeper.
Step 8. Assemble and test. Repeat if necessary.

Hope this helps.

Jul 28, 2012 | Hitachi Nt50ae2 18 Gauge 34" To 2" Brad...

1 Answer

How do you replace the feeder spring on the Senco Framepro 601


You have to remove two cap (hex) screws at the back of the magazine that go through the frame. Then the magazine should slip easily off the nose piece and the feeder shoe with the feed spring roller will come out the front of the magazine. Install the new spring and roller in the feed shoe and make sure the spring hooks on to the top of the magazine when you slide the shoe back in. Put the magazine on the frame and you'll be back in business.

May 21, 2012 | Senco & Frame Pro 601 Framing Nailer

1 Answer

The spring that holds the nails in the firing position is loose


you can buy a new spring but its a lil tricky to install you have to remove the magazine to do it

Jun 25, 2011 | Hitachi 3 - 1/4" Framing Strip Nailer

1 Answer

How to you replace the recoil spring, is there a trick that i dont know about


Not sure which model you have but there are usually screws on each side of the magazine where it is held on to the nose. Remove those screws and the one that holds the bracket at the rear of the gun body. Once you remove the magazine you should be able to see how the spring is held into place. If you have the model number you can find a tool diagram for it here;

http://www.toolpartsdirect.com/

Jun 22, 2011 | Hitachi 3 - 1/2" Full Roundhead Framing...

1 Answer

My hitachi nr 83a leaks air at the trigger


Often a trigger leak in the NR83A is caused by a bad gasket in the head #877-327. If this is improperly installed, cracked, or overcompressed it will cause the trigger to leak.
It is uncommon for the trigger itself to be the problem.

Sep 24, 2010 | Hitachi Nr83a- Strip Nailer-driver Blade...

1 Answer

It will double fire sinking second nail only half way. This happens every third or fourth shot. The nailer is a Hitachi NR 83A 3.25in. X .131


the pin pushing your nails is loose and the guides are warned .
try to change the guides and you will see that this problem will will be gone .
one last thing , make sure the coils are in good shape as it may create some feeding problems and push 2 nails at once

Sep 26, 2009 | Hitachi VH650 2 1/2" Full Head Fencing...

1 Answer

On the Hitachi NR83A2 nailer. Where does the end


Hi,
It goes thru the same hole as the magazine bolt on the nose. Sounds like yours is broken.

Sep 25, 2009 | Hitachi NR83A2 2" To 3 1/4" Full Head...

2 Answers

Reassembling the Hitachi NR 83A2 (S) magazine


The reason that you are having trouble re-assembling the ribbon spring is that you need three hands to complete the job. As you recall the nail pusher just slips into the front of the rails. The pusher has the spring and a pin to retain the spool in place. Install the spring with the bolt hole towards leaver and slip into the front of rails. Take a small paper clip and bend a small hook to catch the ribbon spring. Hook the springs bolt hole with the paper clip and hold the spring in the approximate position for bolt as you push the assembly into rails and use latch to hold. While holding spring with paperclip, insert bolt thru rails and spring into nosepiece. Just break off the paperclip at this point and you are almost done. Some nailers have a metal support clip that you would need to have in place on bolt before installing bolt thru spring. For a breakdown of the gun go to www.toolpartsdirect.com. The other bolt for rails has a support/guide for the safety foot. Good luck and email if you have questions.

Apr 11, 2009 | Hitachi NR83A2S Framing Nailer, Full Head,...

Not finding what you are looking for?
Hitachi NR83A2S Framing Nailer, Full Head, Plastic Strip Collation  Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1383 Answers

Joe Garcia
Joe Garcia

Level 2 Expert

205 Answers

bwbconstruct

Level 1 Expert

23 Answers

Are you a Hitachi Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...