Question about THQ WWE SmackDown! Here Comes the Pain for PlayStation 2

Open Question

Howtoblast the stage

Stage

Posted by on

  • Derek Powers
    Derek Powers May 11, 2010

    What do you mean exactly?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

WHAT IS THE DIFFERENCE BETWEEN A SINGLE STAGE SNOW BLOWER VS A DUAL OR MULTI STAGE SNOW THROWER


Single stage has one rotating blade that collects and exhausts via upper shoot.


26373343-4yt0j151ox44pteg2g1nkeph-2-0.jpg Two stage has one blade for gathering into the center and a second that exhausts via shoot.


The two stage works best!!
26373343-4yt0j151ox44pteg2g1nkeph-2-2.jpg

26373343-4yt0j151ox44pteg2g1nkeph-2-5.jpg Hope this helps?

Nov 26, 2016 | Garden

1 Answer

Hi , can you tell me what is the torque settings for Main,biggens and head bolts for Opel combo 1.4 16v 2006 model z14xep motor?



STANDARD TYPE GM ROD BOLTS
STAGE 1---18 LB/FT (GRAPHITE GREASE UNDER HEAD, OIL THREADS)
STAGE 2---30 DEG's additional bolt head rotation.


CRANK BOLT
GRAPHITE GREASE UNDER HEAD & WASHER, OIL THREAD
STAGE 1---70 LB/FT
STAGE 2---30 DEG's additional bolt head rotation.
STAGE 3---15 DEG's additional bolt head rotation.
CYLINDER HEAD BOLTS for standard gaskets
GRAPHITE GREASE UNDER HEADS & WASHERS, OIL THREADS
SEE SEPARATE SHEET FOR TIGHTNING SEQUENCE
STAGE 1---18 LB/FT 25NM
STAGE 2---90 DEG's additional bolt head rotation.
STAGE 3---90 DEG's additional bolt head rotation.
STAGE 4---90 DEG's additional bolt head rotation.
STAGE 5---45 DEG's additional bolt head rotation.

Nov 06, 2016 | Opel Cars & Trucks

1 Answer

What does the code b0026 mean on my 2009 buick lacrosse?


DTC B0026: Driver Frontal Deployment Loop (Stage 1) Open
It has to do with air bag system
B0026 Stage 1 or B0044 Stage 2 ?€¢
The steering wheel module stage 1 or stage 2 high circuit is less than 2.4 volts and the steering wheel module stage 1 or stage 2 deployment loop is more than 6 ohms for 500 milliseconds.


?€¢
The steering wheel module stage 1 or stage 2 deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.



has to do with

Jun 30, 2015 | 2009 Buick LaCrosse

2 Answers

I want to know the torque opel corsa lite 1.4 cylinder head bolts.


stage 1 ... 25 Nm (18 lb ft)
stage 2 ... angle tighten + 90 degrees
stage 3 ... angle tighten + 90 degrees
stage 4 ... angle tighten + 90 degrees
stage 5 ... angle tighten + 45 degrees

Feb 26, 2015 | Opel Corsa Cars & Trucks

1 Answer

Torq settings on 3.7 cyl heads


This is the info for the 2.8d CRDI 2008-11 engine code ENS (51C)

1 Replace Head Bolts
2 Stage 1 Tighten to15 Nm
3 Stage 2 Tighten to 30 Nm
4 Stage 3 Tighten to 85deg
5 Stage 4 Tighten to 85 deg
6 Stage 5 Tighten to 85 deg

Sequence

w93gwmwpatg0gaaaabjru5erkjggg==
If it is the 01-08 model 2.8 CRD engine code R2816K4 then it is this one
Stage 1 - Bolts 1 -18 = 30 Nm
Stage 2 - Bolts 1 -10 = 75 deg
Stage 3 - Bolts 11 - 18 = 50 deg
Stage 4 - Bolts 1 - 18 - 75 deg

Sequence
aa5xdif9xa+aaaaaaelftksuqmcc

If it is the Grand Cherokee then they fit 3.0 CRD, 4.7, 5.7 and the 6.1 SRT-8 engines. I can supply the details if needed. I hope that helps you.

Feb 04, 2015 | 2008 Jeep Cherokee 2.5

1 Answer

Hi I need the torque settings for both the cylinder head and the bottom end bearings for a 1997 Toyota Prado (3.4litre petrol). Thanks


1997 Toyota Prado 5VZ-FE
Cylinder head bolts:

Tighten the cylinder head bolts in criss cross manner inside out, in four stages as under:
Stage 1. Torque the bolts up to 17 Nm.
Stage 2. 34 Nm.
Stage 3. Rotate all the bolts 90 degrees.
Stage 4. Finally rotate all the bolts further 90 degrees.

Main Bearings:
Tighten the main bearing bolts in two stages, as under:
Stage 1. 61 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Big end bearings:
Tighten the big end bolt of connecting rods in two stages as under:
Stage 1. 25 Nm.
Stage 2. Rotate the bolts further 90 degrees.

Feb 27, 2014 | Toyota Land Cruiser Cars & Trucks

1 Answer

Cylinder head torque specs for opel corsa 8valve 1.4l 2005 model


Corsa 1.4I Engine code Z14XE 2000-2004
Bolts must be renewed
stage 1. 25Nm
stage 2, + 90 degrees
stage 3. + 90 degrees
stage 4. +90 degrees
stage 5. + 45 degrees
Sequence
10 6 2 3 7
9 5 1 4 8
bolts 7 & 8 are nearest to the flywheel side of the engine
Engine code C14NZ 1993-1998
Stage 1. 25Nm
stage 2. + 60 degrees
stage 3. +60 degrees
stage 4. + 60 degrees
Sequence as above.
Corsa 1.4I Engine code Z14XE 2000-2004
Bolts must be renewed
stage 1. 25Nm
stage 2, + 90 degrees
stage 3. + 90 degrees
stage 4. +90 degrees
stage 5. + 45 degrees
Sequence
10 6 2 3 7
9 5 1 4 8
bolts 7 & 8 are nearest to the flywheel side of the engine
Engine code C14NZ 1993-1998
Stage 1. 25Nm
stage 2. + 60 degrees
stage 3. +60 degrees
stage 4. + 60 degrees
Sequence as above. <br />Corsa 1.4I Engine code Z14XE <b>2000-2004</b><br />Bolts must be renewed<br />stage 1. 25Nm<br />stage 2, + 90 degrees<br />stage 3. + 90 degrees<br />stage 4. +90 degrees<br />stage 5. + 45 degrees<br />Sequence<br />10 6 2 3 7<br />9 5 1 4 8<br />bolts 7 & 8 are nearest to the flywheel side of the engine<br />Engine code C14NZ <b>1993-1998</b><br />Stage 1. 25Nm<br />stage 2. + 60 degrees<br />stage 3. +60 degrees<br />stage 4. + 60 degrees<br />Sequence as above.

Jan 09, 2013 | Opel Corsa Cars & Trucks

2 Answers

Mitsuibishi pajero 4m40 engine measuement of torque setting


Cylinder head (renew bolts)

stage 1 50nm
stage 2 100nm
stage 3 slacken of 360"
stage 4 tightn 50nm
stage 5 90"
stage 6 90"

stage 7 tighten the M8 bolts (the smaller ones) 24nm

Main bearings

20nm
90"
90"

Big end bearings

50nm
90"-100"

flywheel 125nm-135nm

Feb 10, 2011 | Mitsubishi Montero Cars & Trucks

1 Answer

Hi, im rebuilting a 88 2.0l 8v and i need the torque mesure for the block and head bolt thx


Eng.code 3A- Cyl.head-stage 1-40Nm,stage 2-60Nm,stage 3-180degrees. Main bearings - stage 1 - 35Nm, stage 2 - 65Nm, Big ends - stage 1 - 30Nm, stage 2 - 90degrees. Flywheel - stage 1- 60Nm, stage 2 90degrees. Eng.code AAD - All torques same as engine 3A. cheers

Dec 01, 2009 | 1988 Audi 80

1 Answer

What should i torque the head bolts to on a 2001 ford 3.0litre engine?also the torque for the intake also!?


for a 3.0 2v....new head
    1. Install the bolts.
    2. Tighten the bolts in five stages in the sequence shown.
    • Stage 1: Tighten to 50 Nm (37 lb-ft).
    • Stage 2: Loosen the bolts one full turn.
    • Stage 3: Tighten to 30 Nm (22 lb-ft).
    • Stage 4: Rotate each bolt 90 degrees.
    • Stage 5: Rotate each bolt an additional 90 degrees.
  • intake bolts are:
    1. Install the intake manifold. Tighten the bolts in the sequence shown in two stages.
    2. Stage 1: Tighten to 15 Nm (11 lb-ft).
    • Stage 2: Tighten to 32 Nm (24 lb-ft).
    • work from the center out
  • Jul 07, 2009 | Ford Taurus Cars & Trucks

    Not finding what you are looking for?
    THQ WWE SmackDown! Here Comes the Pain for PlayStation 2 Logo

    Related Topics:

    49 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top THQ Video Game Consoles & Games Experts

    Timllfixit

    Level 3 Expert

    2210 Answers

     Shayaan Tanwir
    Shayaan Tanwir

    Level 2 Expert

    83 Answers

    CiNi

    Level 2 Expert

    144 Answers

    Are you a THQ Video Game Console and Game Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...