Question about Bosch Plumbing

1 Answer

Find a pump in your products

We have a external gear pump in our factory with the following spesification
pump capacity[2.9 l/min] ,electro motor power 0.75 kw
I want the bocsh product code to order the new pump
and i want to know the exact specificatin of your similar pumps
please respond me as soon as possible
thanx in advance.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Hmm, this is a website where people post solutions to problems,

if you have a model number go to and search for that number

Posted on Jan 05, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Engine on but do not pump water

Be sure the inlet and outlet lines are clear. This has a limited suction lift 23' max, be sure you are not exceeding that or the maximum head. each foot is 0.433 Psig so 98 * .433 = 42.43 PSIG.

Specifications Type Self-priming/Centrifugal Caliber 2 in. Maximum Capacity 160 gal / min Total Head Suction Head Self Priming Time 120 sec / 16 ft Engine Type Air-Cooled, Four-Stroke Rated Horsepower 4.0 @ 4,000 rpm Bore x Stroke 56 x 50mm Displacement 123cc Cooling Forced Air Lubrication Splash Oil Capacity Starting Method Recoil Ignition System Transistor Controlled Dimensions Fuel Tank Capacity 1.2 gal. Recommended Fuel Unleaded Regular Dimensions (LxWxH) Dry Weight A-20070116-1378-130-E

Dec 08, 2013 | Yamaha YP20G Water Pump 2-Inch, 160 GPM...

1 Answer


Motor has failed or the pump has failed and is causing heavy load on motor.

Only other thing to check is the cap, if it is good, look for a new motor if the pump has been working ok.

Aug 21, 2012 | Robinair 15150 1.5 Cfm 2 Stage Vacuum Pump

1 Answer

What in addition to a pool pump capacator is damaged if the capacator shorts against the grounded cover

If the capacitor was grounded for more than just an accidental touch, it could possibly short the start windings.

Jun 18, 2010 | A.O. Smith SQ1102 Pool Pump Motor

1 Answer

Motor screws, Myers 1/2 horse well pump

Sometimes you need to pri upward and turn the screws at the same time.

Apr 13, 2010 | Plumbing

1 Answer

Flotecpump runs for 5 minustes or less and shuts down due to over


With a 1-1/2 inch suction and a 2 inch discharge, you have no backpressure, and it's actually beneficial to have a working head. Try pinching the discharge valve to maintain a steady discharge pressure of at least 20-30 psig on the pump case. Tinker with the discharge pressure as required to balance the pump. As a general rule, the suction line is never smaller than the discharge line to prevent cavitation of the pump. A temporary move of pinching the discharge will compensate some, but it is better to increase the size of the suction line, if the pump will handle it. If the rated pump volume is low, you may also be trying to exceed it's capacity, and heat wil result in the motor.
If at all possible, convert the voltage to 220v as this will also make you more effecient and pull half the amps. Most pumps can be wired either way, and usually the diagram for swapping is included or inside the motor housing. Converting is easy.
Best regards, --W/D--

Aug 25, 2009 | Plumbing

1 Answer

Foltec 4012-10 motor get hots and kicks off

Sounds like a seized bearing. Many times the motor boosts its torque output to get over the initial inertia. and if the bearing seized, the motor running at normal capacity would not be strong enough to rotate. thus causing the rotor to stall and hence the motor getting overheated.

Aug 10, 2009 | Flotec Corrosion Resistant Shallow Well...

1 Answer

Pump goes on and off too often

Your pump is overheating. Check the current draw of your pump during operation. The amperage should not go above its current rating.
Remember Power (Watts)= Voltage (VAC) x Current (Amps). For a 100 Watt motor running at 120 VAC then the current I should see is approximately, 1.2 Amps. If I see 2 amps draw on the motor then I now its about to burn up or another problem has occurred. Values higher then 1.5 times the nominal operating current shows problems with motor or motor operation (excessive load, bad bearings, exc.)
Make sure that the pump is fully primed during entire operation. Note: Pumps hate cavitation and dry run times!
If all of the above is ok, then you may need to increase the capacity of your pump or place two of the same pumps in series for the extra head pressure.

Aug 02, 2009 | Amana Plumbing

1 Answer

Where can I find a replace thermal overload protector? for the capacitor.

See if there is another part number for that breaker (CET51 ABM).

Feb 28, 2009 | A.O. Smith SQ1102 Pool Pump Motor

Not finding what you are looking for?
Plumbing Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Plumbing Experts

Brad Brown

Level 3 Expert

13794 Answers

Tom Chichester

Level 3 Expert

26210 Answers

Gil Shultz

Level 3 Expert

3320 Answers

Are you a Bosch Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides