Question about Projection Televisions

Open Question

I have a Monster Power Home Theatre Power Center HTS 950 power strip/surge protector. It "blew" and I can't reset it. Any suggestions?

Posted by on

5 Suggested Answers

  • 2427 Answers

SOURCE: Hello, I have the following :

Verify that the settings on both the Blue Ray player
and home theratere system is set to eighter DoblyDigital 5.1 or Dobly Digital 7.1

Posted on Jul 27, 2008

  • 927 Answers

SOURCE: red color slide on left side of 43UWX10B

Good Day,

Sounds like the TV's convergence circuit has failed:
*Call an Authorized Service Center and them give you an estimate cost of the repair, or
*Repair it your self; get KIT 10 locally or B&D Enterprises
1-800-458-6053; www.bdent.com.
Good luck, big IRISH.

Posted on Aug 19, 2008

  • 927 Answers

SOURCE: red color slide on left side of 43UWX10B

Good Day,

Sounds like the TV's convergence circuit has failed:
*Call an Authorized Service Center and them give you an estimate cost of the repair, or
*Repair it your self; get KIT 10 locally or B&D Enterprises
1-800-458-6053; www.bdent.com.
Good luck, big IRISH.

Posted on Aug 19, 2008

  • 1 Answer

SOURCE: I have a KDF 42WE655..while watching tv, I heard a popping sound.

If the lamp is blowing that soon, the cooling fan is not working, or is plugged with dust. I have heard some people have a filter that needs changing or cleaning. Check your manual. The cooling fan is on the optical block and not easy to get to.
Probably a job for a tech.

Posted on Sep 16, 2009

gopakumarg43
  • 68352 Answers

SOURCE: mitsubishi wd-52725 wont turn on. no lights,

Hello
The power regulator board of your Mitsubishi TV is faulty. There are two reasons for this fault. The fist one is with its internal protection fuse, and the second one is with component failure to the power supply board. To retify this fault, for both, you must ahve its service manual to follow. User manual provides details about how to use it; where as service manual will have all the details, circuit boards, schematic diagrams, porcieedings to take out and repair the boards, components and it values etc; I can't send the service manual to you by this window. If you want to do this work by yourself, you must have it with you, while I advice you to proceed the work. To get it, you must have to buy one amoung my service published in FixYa website, or go to Google and typw my nickname "gopakumarg43" in its search box. Click on the link "gopakumarg43 - FixYa". You can access my services there. Fixya has placed me on Google, from where you can get straight to me, by mail assistance. I can't touch you by mail, as it is against our Primium Expert's rules and regulations.
The power supply of your TV should be checked. If you have knoledge in electronics and have a concept of soldering, get me by Fixya. OK.

Posted on Nov 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flashing Lamp light, no picture KDG42WE655


Hi,
The Lamp light of the TV blinks when the Lamp of the TV requires replacement. The model # of the user replaceable lamp block is XL-2100U. You can download the manual of the TV by clicking here. Refer to page # 16 of the manual for further information. Follow the steps below to perform a power reset first:
Try the following steps to check if the issue can be resolved.
Turn off the television.
Unplug the television power cord from the electrical outlet.
Let the television remain without power for 60 seconds.
Plug the power cord back into the electrical outlet.

If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
If the issue continues to occur, service may be required.

Thanks for using Fixya.

Jul 16, 2011 | Sony Grand WEGA KDF-42WE655 42" Rear...

1 Answer

Turn on tv and standby light flashes 6 times


The self-diagnostic function of the projection TV will cause the STANDBY light to blink or flash when the television detects an issue.

Follow the steps below to perform a power reset:
  1. Turn off the television.
  2. Unplug the TV power cord from the electrical outlet.
  3. Let the TV remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the TV is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the TV.
  5. Turn on the television. NOTE: If the TV does not turn on immediately, the fan may need to finish its cycle. This is part of the cooling process for some projection TVs and is normal operation. After the fan turns off, attempt to turn the TV on again.

If the issue is still unresolved after following all of the troubleshooting steps, service may be required . Please note the number of times the STANDBY light flashes and relay that information to the service center.

Source

Oct 16, 2009 | Sony Grand WEGA KF50WE610 50" Rear...

1 Answer

I have a sony bravia 60'' projection tv kds-60a3000. the problem is after a couple of minutes i will get no sound or picture. i disconnected the plug from my power strip for 5 minutes to cool down, then...


The STANDBY light will flash if the television detects an issue within the television. Some of these issues can be resolved simply by following the steps below to reset the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required . Please note the number of times the STANDBY light flashes and relay that information to the service center.
  1. Turn off the television. Unplug the television power cord from the electrical outlet.
  2. Let the television remain without power for 60 seconds.
  3. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  4. Turn on the television.

Sep 22, 2009 | Sony Projection Televisions

1 Answer

Sony wide screen projection tv model kp-57wv600 problem. Sound with no picture. Stanby red light blinks seven times? What parts do I need to repair the problem. Thanks ,Gary


I found this solution from SONY's website.

The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.
  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.


I hope this helps.

Jul 19, 2009 | Sony KP-57WV600 57" Rear Projection...

1 Answer

Sony Grand WEGA KF42WE610 42" turns on and off


If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.

Please make sure that the videos sources are connected properly to the TV.

Try Power Resetting the TV.

Please disconnect the power cord from the wall outlet (for approximately 1 minute), then reconnect the power cord and check whether the issue is resolved.

Also try connecting the TV to a different wall outlet and check if that helps.

Jun 16, 2009 | Sony Grand WEGA KF42WE610 42" Rear...

1 Answer

Ihave a sony KP53S75 TV there was apower surge and now there is no picture. The red light blinks 4 times can anyone tell me about this?


Hi, if this TV was hit by the surge and it was protected by a surge protector, please follow this reset procedure.

The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.
  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.

If the problem is still there and the light is still blinking 4 times, this means that the surge has destroyed the Vertical deflection component. in this case, it will have to be replaced.

please rate and have a great day.

Mar 25, 2009 | Sony KP-53S75 53" Rear Projection...

1 Answer

TV WENT OFF AFTER WATCHING AND NOW IT WON'T GO ON AT ALL


Try to do the following, it didn't work for me but it may work for you...


The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.
  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.

Mar 12, 2009 | Projection Televisions

1 Answer

Red color slide on left side of 43UWX10B


Good Day,

Sounds like the TV's convergence circuit has failed:
*Call an Authorized Service Center and them give you an estimate cost of the repair, or
*Repair it your self; get KIT 10 locally or B&D Enterprises
1-800-458-6053; www.bdent.com.
Good luck, big IRISH.

Aug 05, 2008 | Hitachi 43UWX10B 43" Rear Projection...

1 Answer

Red color slide on left side of 43UWX10B


Good Day,

Sounds like the TV's convergence circuit has failed:
*Call an Authorized Service Center and them give you an estimate cost of the repair, or
*Repair it your self; get KIT 10 locally or B&D Enterprises
1-800-458-6053; www.bdent.com.
Good luck, big IRISH.

Aug 05, 2008 | Hitachi 43UWX10B 43" Rear Projection...

2 Answers

TV Lamp light blinking


COULD BE FAN NOT WORKING. TAKE BACK OFF SEE IF TURNING, CLEAN THEM. GO TO SONY.COM,TROUBLSHOOTING, OR SHUT THE TIMER OFF.
The STANDBY light is flashing on the television and there is no picture or sound. Solution
sp.gif sp.gif The STANDBY light will flash if an issue is detected within the television. This can sometimes be resolved by simply following the steps below to reset the television.
  1. Turn off the television. IMPORTANT: For a projection television that uses an internal lamp, wait 5 minutes after turning off the television to allow the lamp to cool before continuing with the following steps.
  2. Unplug the television power cord from the electrical outlet.
  3. Let the television remain without power for 60 seconds.
  4. Plug the power cord back into the electrical outlet. NOTE: If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
  5. Turn on the television.
If the issue is still unresolved after following all of the troubleshooting steps, service may be required. Please note the number of times the STANDBY light flashes and relay that information to the service center.

Jul 10, 2008 | Sony Grand WEGA KDF-60WF655 60" Rear...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...