Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool front load washer is not finishing wash cycles & water appearing in barrel

It doesn't happen all the time, but has happened more frequently lately. Will start the load, but does not seem to make it into the rinse/drain portion of the sequence. Will find fabric softener still in tray and all lights completely shut off. Sometimes the clothes will still be soaked with water, too. From time to time have moved clothes to dryer that seem to be fine, and even when the door is left open will return to find the bottom of the wash barrel with standing water in it. However if you put the washer into drain/spin it will kick the water right out into the drain, so I don't think its a pump problem. Any help will be appreciated.

Posted by on

  • 3 more comments 
  • venom2001
    venom2001 Nov 14, 2012

    I cleared the filter and the problem with shutting down in middle of cycle is still happening. Any other ideas?

  • Richard Roth
    Richard Roth Nov 14, 2012

    OK, remove the top of the unit and check all the wire connections. It might be a good idea to unplug them and then re-seat them. Post back after you do that and try a load. Also, open the door, push the bottom of the seal back and see if there is an article of clothing that may have gotten in there.

  • venom2001
    venom2001 Dec 06, 2012

    I've checked the connections on the control board, opened the filter again, no clog, and nothing inside seal. The machine will make it through a full cycle 50% of the time. The rest of the time the wash light and add garment light will blink throughout the beginning of a cycle, and then the unit just shuts off. I'm thinking it's probably the control board.

  • Richard Roth
    Richard Roth Dec 06, 2012

    Yes, you will need to replace the control board. Here is the part to order.http://bit.ly/TVJYl7

  • venom2001
    venom2001 Dec 08, 2012

    Thanks for your help.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Whirlpool Master
  • 9,472 Answers

First, check the filter to be sure it is clear.

Posted on Nov 06, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 662 Answers

SOURCE: Washer stopping mid-cycle with no error

Remove the 3 screws at the bottom of the front panel under the washer door. Your filter door will be light brown. If you find a hose there it is to drain out excess water (water that could not be drained by your pump) After you have drained, unscrew the cap and remove all the junk inside. Have a large plastic bag to catch junk and water. Refit carefully after cleaning out. If not solved, something shd be blocking your pump, check this out. F-21 filter blocked.

How abt a nice rating for the free help?

Posted on May 30, 2010

Daniel S
  • 4323 Answers

SOURCE: My Whirlpool Auto Load Sensing

Hi

To reset the Whirlpool washer turn off and unplug it, restart the washer after 30-40 minutes and check if the washer is reset. Let me know if you get any error code after restarting the washer. If no error code appears then the issue can be due to faulty door switch, remove the top cover of the washer and check the connections to the door switch. Hope this helps... Please post back with complete model# if you need more information.

Daniel

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sm8280867


See if all the connections are tight; try inter-changing the water pipes. Water should have good pressure at faucet.......

Apr 27, 2013 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Hi, After just finished washing one load, on


Hello & Welcome to FixYa


This is a common issue with Whirlpool Duet washer however; your washer needs a reset to resolve the control lock problem. Press and hold the END OF CYCLE/CYCLE SIGNAL button for 15 seconds to reset the control. Please get back to me if you have any other questions.


Kevin

Aug 16, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My whirlpool front load keeps cycling without the water filling.


Hi,

If your washing machine will not fill, only hot or cold will fill or is slow tofill then read these tips. I have covered many of the things that can happen inthese tips...


Washing Machine Problems No Water

Washing Machine Fix Washing Machine No Water

heatman101

;'
';
'
;

Apr 30, 2011 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Whirlpool Cabrio: During a white load the machine stops at 38 min


lf means long fill check your fill hoses and make sure the water is comeing out. sounds like a problem with your inlet valve and/or your water from your house is not right.

May 31, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

How do you unlock fh code on duet washer-wife forgot to turn on water & washer locked out-now door won't open & can't clear code by just pushing reset or unplugging-not sure how to maually...


Switch machine off for approx. 10 min. then with water open, try and select a short wash cycle and let it finish. Also push the door firmly in before you retry because you have been trying before to open it.(latch might not be correctly closed).

May 23, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Power is on, still will not start


Too many clothes
washer door not opened between washes
low power/extention cord
kinked hose
Door not shut tightly
hoses connected backwards
inlet screens clogged
circuit breaker tripped
unbalanced load
excessive suds
wrong detergent
Repair Manual

Jan 14, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer fill with water after the cycle is over


well ,either the machine wasnt finished (it may have been doing a second rinse and spin) or the electric valve not shuting. try let it fill and see what happens

Jul 30, 2009 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Whirlpool duet front loading washer


your inlet water valve is not closing and needs replacing, in mean time turn water off between washings.

Apr 28, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2122 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...