Question about Xerox WorkCenter Office Equipment & Supplies
It says Code 09-545.00 (toner gauge disabled). How do I enable it?
This means that the toner is low and the machine is waiting for the empty signal OR it has been disabled as part of a software update. It has no effect on the operation of the machine.
Posted on Jan 12, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: I have a Xerox Workcenter M20i.
You need to replace the fuser. There is a heating coil in the fuser roller that opens. Replace the fuser and it will resolve the problem.
Posted on Jan 25, 2009
SOURCE: Xerox Workcenter 222 toner card
There is a card that should come with a cartridge. It slides into the slot on the side of the machine to reset the toner cartridge count.
I don't know of a way to reset the count without a card.
Wish I had a better answer, but the card is encoded to reset the machines toner count in the software.
Posted on May 06, 2008
Remove the covers. But before you go to eh print head itself, there is a print head pivot block that often gets contaminated with ink. The code you are having, is related to the print head not being able to move freely side to side, or tilt properly.
To access that block. You have ot remove the document feeder and scanner. To do that you disconnect the cable, it runs from the back to the scanner to the opening where the power cord plugs in, remove the 2 thumb screws and unplug it. You slide the doc feeder and scanner back, then depress the two tabs and completely remove it.
There is one screw in the back that holds on both the left and right side covers. You have to lift and kind of twist the covers in about the middle of the machine, The front cover will also pop off, it has tabs that holds the front covers together. Then remove them.
Look on the left side of the machine, looking from the front. You will see a stainless steel block, about one inch square, located about 2/3rd of the way back on the lower 1/4th of the frame. It has a spring and a clip over it. Just pull out on the spring bracket and locate it up and to the left, It is meant to be put there for servicing.
Look at the block. it may be filled up with yellow ink. If so , remove it with channel locking pliers. It may be VERY tight, so work it out slowly. Then soak it in hot water, that softens the ink , and clean it and the shaft thouroghly and remove as much excess ink from teh surrounding area as possible. Also, IF that is the problem. Probably a 75 percent chance, then when you return the printer to service. Get a small level, and make sure the printer is level BOTH side to side and front to back. To do that , you place the lecel on the platen glass, sideways then front to back. Often times those printers are not level and that causes the problem. The other things that happens is simple spill over from the ink catch tray, It is imperative you have those printers sitting level.
If thats not the problem. let me know We will go from here.
Posted on May 18, 2009
SOURCE: our xerox workcenter 7235 fault
024 360 An error has been detected by the Controller during communications with the Printer. User
intervention is required to Power Off/Power On the machine, Field Service is required if the
problem persists. Printing is disabled.
You will have to either get this printer repaired or replace it.
Posted on Aug 05, 2010
Tips for a great answer:
Dec 26, 2012 | Xerox Office Equipment & Supplies
Nov 14, 2012 | Xerox Fuser Cartridge 008R13040 for Work...
Dec 26, 2010 | Xerox WorkCentre PE16 All-In-One Laser...
Aug 05, 2010 | Xerox Office Equipment & Supplies
Dec 17, 2009 | Xerox Phaser 8500/DN Printer
May 02, 2008 | Xerox WorkCentre M20i All-In-One Laser...
1,130 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: