Question about Televison & Video

1 Answer

Powers off Comes on after approx 1-2 minutes shuts down completely

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Televison & ... Master
  • 14,553 Answers

I am here to help but need to know brand and the model number to help.

Posted on Nov 06, 2012

  • skhughes Nov 07, 2012

    I put all that in the original request, but again:

  • skhughes Nov 07, 2012

    It's a Phillips Magnavox Model TS3254 C102 Chassis # 32A500

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hayward H400FDN will not stay lit - Brand New install - NO Fault codes.


make sure wiring is correct especially if wired 120 volt read instructions inside panel

Jan 28, 2014 | Hayward Industrial Products H400FDN...

1 Answer

Jandy LX250-L Burner shuts down and no errors


It is more likely the board on the LX.
If you have a volt meter check the IND connection on the Fenwal for 24volts while running and keep your meter on it until it shuts down. If the power is still present at the IND while shutting down then it would appear to be a Fenwal problem. It sounds like the temp circuit on the board or the temp sensor it self is bad. Try dipping the temp sensor in a glass of water with a confirmed temp to see if it is accurate.

Apr 03, 2017 | Pool & Spa

1 Answer

Samsung HLN507W turns on for about one minute then shuts off, three blinking lights stay on in front. It is not the lamp, nor the blue lamp cover switch for sure. I unplug it and immediately turn it on. ...


Samsung HLN507W turns on for about one minute then shuts off, three blinking lights stay on in front. It is not the lamp, nor the blue lamp cover switch for sure. I unplug it and immediately turn it on. It always does the same thing: comes on for 1 minute, then powers down - there is no wait time in between unplugging and powering on. All fans seem to work and I cleaned the dust out of it. Help.

Nov 04, 2010 | Samsung HLN507 50" Rear Projection...

1 Answer

My vulcan ducted heating unit blows cold air for approx 1 minute when turned on then stops and try's again after approx 1 minute,it does this several times until ignited.It is obviously an ignition...


Two things have to occur here:

1) The ignitor has to light off the gas. A bad ignitor, or dusty burners can prevent ignition.

2) The thermocouple has to be in the flow of burning gas to prevent a safety shut-down, and has to be working.

And the obvious: you need pressure in the gas line, and the gas valve needs to be open.

Hope this helps you locate the problem!


Aug 14, 2010 | Vulcan AUW230A Heater

2 Answers

Steam shuts down after approx.15 minute


I would venture a guess that the heating element has become intermittent with a short. Wasn't so bad before, but played heck with controller due to noise from arcing, but now have a dead short when heater reaches temperature.

Apr 11, 2010 | Mr Steam Mr. Steam MS 81500E AutoFlush

1 Answer

Printer won't start


1. completely unplug power cord from wall socket,
2. unplug power cord from printer
3. unplug printer cable completely from computer
4. unplug printer cable completely from printer.
5. let printer stay disconnected for approx 1 minute
Now securely:
1. reconnect the printer cable to the printer.
2. reconnect the printer cable to the computer
3. reconnect the power cord to the printer
4. reconnect the power cord to the wall socket

turn printer on

You may find that a connection has simply worked itself loose over time.

Mar 29, 2010 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

Furnace pilot problem


check the pilot gas pressure, might be too weak and blowing out when the blower starts, the clicking noise is the gas valve shutting down when it detecks no pilot flame, that park is normal.

Jan 10, 2009 | Honeywell Power Humidifier: Furnace...

1 Answer

Camera turns on then auto shuts down??


when the lens comes out grab it and lightly!!! push it to one side this worked on a cannon i have

Jan 22, 2007 | Casio EXILIM ZOOM EX-Z600 Digital Camera

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73619 Answers

Cindy Wells

Level 3 Expert

5056 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...