Question about Toro Power Lawn Mower

1 Answer

1972 whirlwind push mower

My mower have 'nt been started in three years

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

May just need the carburetor redone. Do you have any photos? Wanting to sell it? Just curious, as I am a Toro collector with at present a 1967, three 1970, two 1971, and a 1981. :-)) David.

Posted on Nov 16, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Early this month I bought from Sears the 30" rear engine riding mower. At the time I did'nt want to pay the 299.00 for the grass catcher. Three weeks later at Sears outlet I found the catcher for...


without a model number what do you expect us to do go to where you bought the mower and ask them for the attachment manual. like make you a copy .

Feb 03, 2015 | Sears Garden

1 Answer

Mower was running until it stop and would'nt start found out the one of the push rod was broke replaced it and now i can't get to start and its flowing out the plug


A broken pushrod can indicate an engine with out of sync valve timing. It may be that a piston slapped an open valve snapping the pushrod...neither one is good, you may need to tear this one down.

Sep 19, 2012 | Garden

1 Answer

Toro whirlwind push mower fuel mix


4 stroke engine, no fuel oil mix.

Aug 08, 2012 | Toro Power Lawn Mower

1 Answer

When installing key in my b/d rechargable mower don't go in easy & won't start


IGNITION COIL BAD PULL WIRES OFF BACK AND HOTWIRE OR REPLACE IGNITION

May 09, 2012 | Garden

1 Answer

My push mower was stored for over a year tipped up, and all the oil leaked out. It won't start now.


The paper air filter will now be soaked with oil, remove the filter completely, remove the spark plug and crank the engine to evacuate any oil above the piston, clean/replace the spark plug and re fit, top the engine oil up if low, now attept to startbthe engine with the filter still removed, once it starts it will smoke heavily until it clears the oil in the bore.

Mar 04, 2012 | Poulan "Poulan" Push Mower

1 Answer

I have weed eater/poulan 22" push lawn mower. It


Hi goldengear...

Make sure you have installed the blade on the right way, if it is installed upside down then it will "beat" the grass instead of cutting it and make a terrible cut, also make sure the blade is good and sharp.
The rough running may be due to trash in your carburetor, I would advise to clean your carburetor and also check you fuel tank for trash, water,etc. if there is any trash,water,etc in there then you need to also clean the fuel tank.
Do one more thing and check/clean/replace your fuel filter if you have one.
Please take time to rate me

Aug 18, 2011 | Poulan "Poulan" Push Mower

1 Answer

Need piston clearance value on a rebore for a 1964 Honda c105 and can push rods be straightened? Frame# c105-0040778 what year?


Piston clearance is .002. The push rods can be straightened, be careful not to crush them. It's also not critical that they are perfectly straight. Not sure about the year, Honda actually didn't create "model years" until 1972. They used a letter and # designation (for example, 68-71 CB 750's are K1) until the changed something about the bike.Good luck!

Jun 09, 2011 | Honda Honda Passion Plus Motorcycles

1 Answer

After the engine began hunting i cleaned out the carb ,jets etc & replaced the carb diaphram & gasket correctly ,now it wont even start,there is a good spark but the plug is dry when removed...


did you replace you diaphrams or just clean them, does it have a float bowl or just diaphram? sounds like during all you cleaning you did'nt adj the tab to the needle, therefore diaphram is not opening needle which is not giving gas to the carb. tab should be flush with carb body and when you push on it needle should move to open and let fuel in, good Luck

Apr 27, 2011 | Briggs & Stratton Garden

3 Answers

Changing belt - Eureka Whirlwind 5740


I tried the website for manuals but no luck. I called the toll-free # 1-800-282-2886 and got a rep right away. I gave him the model and s/n (lower bottom on the back side) and he walked me thru it. For the model I have, there are 3 screws to remove - With the vacuum upright and standing facing it - there is on on the right and one on the left of the bottom cover and one on the left side near the hose intake. Remove those to get to the belt. I ordered the belt with him too - althought the belts were cheap ($2.99 for 2) the shipping was $8. If this didnt help - call the 800# - they were great.

Dec 08, 2008 | Eureka Whirlwind Litespeed 5740 Bagless...

Not finding what you are looking for?
Toro Power Lawn Mower Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toro Garden Experts

Joseph Mueller
Joseph Mueller

Level 2 Expert

338 Answers

Mike Squire

Level 2 Expert

391 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Toro Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...