Question about Myryad M Series MI 120 Amplifier

1 Answer

Myryad MI 120 Failure

System powers on, lights flash and then hold steady as always...but there is not that familiar *click* that comes when the flashing stops. No audio can be heard through the speakers.
Any ideas? Is this a simple repair?

Posted by on

  • Anonymous Feb 23, 2009

    I have the same amp and problem, where can I find a repair shop on the east coast?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

This is a serious amp problem either relay has died doubtful,sounds like protection circuit is active due to a dc problem in board

Posted on Jan 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No out put on right channel


Check output transistors and drivers change emitter resistors

Dec 31, 2013 | Myryad Z Series Z160 Amplifier

1 Answer

Myryad ma120 power amp,loud pop when switched off


Sounds like a Electrolytic capacitor has failed. Search backwards from the speaker connections inside the unit to the main PC board. Replace the first ones that you come accross that are linked with the speakers.

Dec 15, 2012 | Myryad Z Series Z160 Amplifier

1 Answer

McIntosh MC7106 Amplifier not powering up


It can be a variety of reasons but I feel that your amplifier is shutting off after powering on. There is nothing that can be done from the outside but If you are familiar with basic electronics and can attempt to take a look I can try. Open the set after you have pulled off the power, then look into the set and tighten all the connectors and cords. Power on and see where the click comes and goes off. If the relay is not holding on then your protect circuit is shutting it off. Armed with a multimeter turn on the power and check if the main +B power is coming to the output stages.If there is momentary swithch on , then disconnect power and test the continuity in the output stages. If hsort open the leads to the output section and then power on. If the relay stays we have found the fault. you can go on to change the failed outputs. If however the outputs were tested ok, then your fault could be the relay or the protect circuit, Hold a rely for a moment to see if the amplifier powers on, if so check the relay drive transistor , the biasing to the stage. Try this out and I hope my advice helps. Good day

Jul 21, 2010 | Audio Players & Recorders

1 Answer

Volume output level is low on all channel.


Please disconnect your speaker and using a good 1.5 AA cell test for a good response. if Ok connect to the amp and power. Hope you are using the right source input. If not give you input to another source input and check. If not it is important to check with a signal test for the failed section. Attempt this only if you are familiar or else ask a friend to test from the output backwards to find the section which is not responding and attentuating. It sould be a possible failure in the premap/ input selection or a biasing of these circuits. Hope this helps. Good day

Jun 10, 2010 | Myryad M Series MDP 500 7.1-Channel...

2 Answers

Primare A30.2 power amp has stopped working. Mains fuses are ok. Green light remains flashing - & amplifier inactive - even after normal warm up period (approx 10 seconds) when it would normally show a...


Hi...

It sounds like you have an output amp failure and it looks like you paid good money for it.

If it's under warranty, find a service place. If not let me know your location and I can suggest someone to fix it

Apr 02, 2010 | Audio Players & Recorders

1 Answer

Line six guitar amplifire...controls


Hi! I have a Spider III 15 watter, but I think the functions are similar. If the "Tap Tempo" light is flashing, you are not in Reverb mode. The light must be lit steady if you are in "Reverb" mode. I notice that you have to rotate the knob that you're working with all the way counterclockwise, and then clockwise to the setting you're trying to get. If you just turn it clockwise from where it is when you power on, it doesn't seem to do much to change the settings. Also, very little movement of the knobs makes a big change. They seem to be very sensitive.
You may want to reset your amp to the factory default settings. This will clear ALL presets that you have saved! To do this, hold down the CLEAN channel button when you power it on. Again, ALL SAVED PRESETS WILL BE CLEARED! Hope this helps.
The Line 6 forums are a great place for info. They will even tell you about "Secret Settings" that are not in the manual. Good luck and rock on!

Oct 03, 2009 | Audio Players & Recorders

1 Answer

Power requirement


David, rest assured you can purchase a VOLTAGE CONVERTER and use it overseas to adapt to other voltages. I would recommend you pick one up at any electronic dealers or check online as to what is available, GOOGLE: Power Converters Be sure to obtain one close to the wattage your unit requires

Feb 22, 2009 | Myryad M Series MDP 500 7.1-Channel...

1 Answer

Myryad MA500 blown channel


Try the repair directory on this site

Nov 20, 2007 | Myryad M Series MA 500 Amplifier

1 Answer

Pre-amp locks up


Check the repair dirctory at the bottom of this site

May 26, 2007 | Myryad M Series MDP 500 7.1-Channel...

Not finding what you are looking for?
Myryad M Series MI 120 Amplifier Logo

Related Topics:

560 people viewed this question

Ask a Question

Usually answered in minutes!

Top Myryad Audio Players & Recorders Experts

kakima

Level 3 Expert

98694 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

The Knight
The Knight

Level 3 Expert

69649 Answers

Are you a Myryad Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...