Question about Mr Steam Ms Super 1e Steam Shower Generator

1 Answer

I have the Mr Steam MS Super 1 T steam unit with the Tempo Plus accessories and auto flush. The unit has worked great for about 2 years but for some reason yesterday the unit light comes on at the controls, the unit fills with water and it does not produce steam. Can ne something other than the heating element since it is still fairly new?

Posted by on

  • mmzgwilliams
    mmzgwilliams Nov 05, 2012

    I checked the unit and water fill, unplugged and replugged accessories, turned power off and on. House is double filtered with dual water filtration by Steris, so build up does not seem to be possible, especially with auto flush installed.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

You would need a multi-meter or voltmeter to trace the power path. Turn on the generator and wait until you hear the water feed solenoid stop. This means the water has reached the satisfied level and the pc board should have sent 24v to engage the contactor. On the actual pc board there is a section label "cont" which is what sends the 24v to the contactor the engage the heating element. Verify that you have 24v on the spade terminals going out to the contactor, if not then you may have a pc board issue. Second possibility is the contactor, if it is recieving 24v and it is not engaging then it's simply a bad contactor. Check the load side of the contactors with the blue wires. Lastly if these two steps check ok, then perform an ohm reading with a multimeter on the actual heating element(with the power off, put your two test leads on the two flathead screws that hold down the blue leads the go to the heating element). If you get an open reading then this may indicate a failed heating element. Pulling the heating element out on the left side panel will confirm any element failure.

Posted on Nov 08, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

frcs68
  • 1605 Answers

SOURCE: When I turn on my steam unit it powers up takes

go to the following link
http://www.manatron.net/Pdf's/Sussman/residential.pdf
the manual may help you with yur problem.
it is hard to say what is wrong without looking the actual unit.

Posted on Apr 07, 2009

  • 143 Answers

SOURCE: Steam Shower shuts down immediately now.

probably scale build up from tap water unfiltered. Scale caused by mineral deposits will affect safety systems and auto cut offs in the unit

Posted on Sep 13, 2009

  • 1 Answer

SOURCE: Mr. Steam CU-750 not working

CU - 750 - the unit fills, element energizes, it doesn't make steam.
The element was installed two weeks ago. If the element went bad so soon, what could have caused this?

Posted on Mar 01, 2010

  • 1 Answer

SOURCE: error code Prr

I had this problem, and checked the connections, emptied the resivour, and refilled it, and it had no effect.
To fix the problem, I ran the regular shower on hot for 10 minutes to warm up the shower chamber. Then, when I pressed the power button on the steam shower, it displayed "110" as normal.
The problem with "Prr" appears to be that the temp sensor is reporting a value out of range. Heating the shower chamber (and therefore sensor) provides a good value to the sensor, which then allows the shower to operate.
Try warming up your sensor by running the shower.

Posted on Mar 06, 2010

  • 1 Answer

SOURCE: Mr. Steam steamer is inppoerable

I just got this problem too, any solutions or a link to the manual?

Posted on Aug 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mr Steam MS Super-1 kW: 10 doesn't generate steam


the first thing the generator should do when you hit the on button is fill. You will hear the water entering the tank. Once the water stops it indicates that the water has reached the water satisfied level, after which you should hear a loud click(your contactor engaging for the heat cycle, newer units will have all three light on the side lit). After this point is you aren't getting any steam after 5 minutes it probably means your heating element may be damaged. It would be best to remove the element at this point from the left side of the unit via 6 bolts and 2 wire leads. Any physical damage on the element such as a pinhole pop, burn mark, melting, or scar will surely prevent the element from heating

Jan 10, 2014 | Mr Steam Electrical Supplies

2 Answers

I have a Mr. Steam unit installed in my shower room. When i turn the steamer on it sounds like it is working and the lights are on but no steam coming through!!


Hi I am with Mr. Steam Tech Support please call 1-800-767-8326 and ask for tech support we will also need you model and SN that are located on your steam unit

Nov 27, 2010 | Mr Steam Hardware & Accessories

1 Answer

Steam shower wont turn on getting a flashing temp on controller in shower


Hi I am with Mr. Steam Tech Support please call 800-767-8326 and ask for tech support. please have your serial number and we will be able at assit you in getting your unit up and running
Thanks
Mike
Mr. Steam
Product Support

Nov 14, 2010 | Mr Steam Ms Super 1e Steam Shower...

1 Answer

My mr steam is not steaming. We turned it on and 20 minutes later nothing happened. WE tried jump starting it with pouring cold water and that helped but it didn't reallly build up much of a stem before...


Hi my name is Mike with Mr. Steam Tech Support please call 800-767-8326 and ask for Tech Support and I will be more than happy to help you with you problem. please note I will need your model and SN Thanks
my ext is 1280
Dan ext is 1288
Mel ext is 1275

Sep 27, 2010 | Mr Steam Mr. Steam Steambaths Bulter...

1 Answer

We just moved into a house with a MS150 Mr steam. I turn it on and the display reads 110 for 10 mins then comes up with H2O on the display. What do I have to do? Nothing seems to happen.


Hi my name is Mike with Mr. Steam please give me a call at 1-800-767-8326 and ask for tech support. We will need you model # and SN # that is listed on your unit if you can be by your unit when you call and we will help troubleshoot your unit. In the mean time check the following 1) water is on 2) drain valve closed even if you have a auto flush close manuel valve for testing
Thanks
Mike Nail
Mr. Steam

Sep 18, 2010 | Mr Steam MrSteam MS150E Steam Generator

2 Answers

Steam shuts down after approx.15 minute


I would venture a guess that the heating element has become intermittent with a short. Wasn't so bad before, but played heck with controller due to noise from arcing, but now have a dead short when heater reaches temperature.

Apr 11, 2010 | Mr Steam Mr. Steam MS 81500E AutoFlush

2 Answers

Mr. Steam Prr erro


Hi, kindly check the connection of your temperature probe down to the main board maybe its loose.

Oct 03, 2009 | Mr Steam Mr. Steam MS 81500E AutoFlush

1 Answer

Error code Prr on Mr. Steam control unit. Steam generator starts for about 10 seconds, but no steam comes out and error code "Prr" shows on control unit. Any insights?


I had this problem, and checked the connections, emptied the resivour, and refilled it, and it had no effect.
To fix the problem, I ran the regular shower on hot for 10 minutes to warm up the shower chamber. Then, when I pressed the power button on the steam shower, it displayed "110" as normal.
The problem with "Prr" appears to be that the temp sensor is reporting a value out of range. Heating the shower chamber (and therefore sensor) provides a good value to the sensor, which then allows the shower to operate.
Try warming up your sensor by running the shower.

Sep 15, 2009 | Mr Steam Mr. Steam MS 81500E AutoFlush

1 Answer

When I turn on my steam unit it powers up takes


go to the following link
http://www.manatron.net/Pdf's/Sussman/residential.pdf
the manual may help you with yur problem.
it is hard to say what is wrong without looking the actual unit.

Apr 06, 2009 | Mr Steam Mr. Steam Allegro Sauna Model...

Not finding what you are looking for?
Mr Steam Ms Super 1e Steam Shower Generator Logo

Related Topics:

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mr Steam Electrical Supplies Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Hippy_dd

Level 2 Expert

110 Answers

ray gallant

Level 3 Expert

41394 Answers

Are you a Mr Steam Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...