Question about Hotpoint 24 in. BF72 Built-in Dishwasher
Quick wash showing 38mins, all other 3 settings showing 99mins (not normal). Problem is that when we do a wash the dishes have a **** left on them, or not washed properly. Program's seem to have got mixed up and stopping mid cycle although timer says '0'.
If you are using hot water connection then check the temperature of incoming water is hot enough. If cold water inlet only is used then most likely the heater element or thermostat in the dishwasher is faulty and the water is not heating enough.
Posted on Nov 05, 2012
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: HOTPOINT DISHWASHER FDW60
I have just had my dishwasher fixed by Hotpoint, as the heater was working and the dishwasher only stopped with the fast and delicate lights just before the drying process he replaced the main control board. This has solved the problem, I suspected the fault to be the thermistor as the heater seemed to be getting to hot but I had no idea where it was.
It turns out the thermistor is attached to the main control board and hangs down behind the front door that gives just a rough temperature level for the main control board.
As it's soldered directly onto the control board I would suggest replacing the whole control pcb for anyone with this fault unless you can find any spec details for the thermistor.
Posted on Mar 23, 2008
you may want to check and clear the pump
you have something slowing your drain
but for giggles make sure your float valve is free to go up and down like it should
all dishwashers attempt to drain first
so you have a conflict between the float position and the pump sensor
Posted on Oct 08, 2009
There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....
Dishwasher Repair Problem Detergent Cup does not Open
Posted on Sep 30, 2010
SOURCE: I have an hda3400go2ww, and
White film deposits are observed if water is hard or when you are using more detergent than needed, try filling detergent cup half way. Try using white vinegar after the wash cycle is complete, run a complete cycle. Also turn down the heat on the hot water fed to the dishwasher. Try using water softener for better results.
You can also add vinegar in the final rinse cycle.
Hope this helps... Please post back if more information is required.
Posted on Oct 26, 2010
Tips for a great answer:
Sep 25, 2014 | KitchenAid Dishwashers
Nov 15, 2013 | Electrolux Dishwashers
Mar 11, 2011 | Kenmore 24 in. 17483 Built-in Dishwasher
Feb 23, 2011 | Miele 24 in. G646SC Plus Free-Standing...
Sep 28, 2010 | Hotpoint 24 in. BF72 Built-in Dishwasher
Jun 05, 2010 | Jenn-Air 24 in. JDB1090AWS Stainless Steel...
Nov 24, 2009 | Maytag Neptune FAV6800AW Top Load Washer
Feb 11, 2009 | Bosch 3.81 cu ft WFMC530 1UC Nexxt 500...
Sep 13, 2008 | Kenmore Oasis HE 27062 Top Load Washer
Sep 12, 2007 | Bosch 24 in. SHE44C02UC / SHE44C06UC /...
110 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: