Question about Vehicle Parts & Accessories

Open Question

How to reset a remote j5f- tx2000 astrostart - Vehicle Parts & Accessories

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Bought a car with an old Astrostart remote

i have an astro start remote but i tried to hook up a trailer brake now the vehicle wont start

Posted on Apr 03, 2010

Logjam
  • 159 Answers

SOURCE: Replace batteries on j5f- tx2000

You have to put the key in the ignition and turn it clockwise to the run position inside of a minute after you open the door.

Posted on Jan 31, 2011

  • 4961 Answers

SOURCE: Astrostart J5f Tx2000

You might want to post this question in a different section. This is the computer games section.

Posted on Jul 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why would my Aerostart j5f-tx2000 remote key fob not transmitting


I would suspect it needs the power cell in the key fob replaced.
It may have enough electricity left to work the little LED indicator but not enough to transmit. If this is the fob you use most of the time it would make since that the battery would be depleted before the other just because of the higher use.

Replacing the battery cell in the fob is what I would try first.

Sep 04, 2016 | 1995 GMC Yukon

1 Answer

I have an Astrostart hst5224, It will star then immediately shut off. My jeep is A manual transmission


[PDF]MODEL RSS-5225 - DirectedDealers.com

www.directeddealers.com/manuals/OG/Astrostart/RSS-5225_OG-Eng.pdf
Immediately report any malfunction to the AstroStart dealer that performed the ... Always turn off the main switch when not using the remote starter for .... The startmodule will inform you of the status of door locks, the alarm and of the engine. .... If the trunk is opened for more than 5 minutes, the system switches to the.

How do you reprogram an AstroStart remote HST5224

www.answers.com > Wiki Answers > Categories > Cars & Vehicles
In order to reprogram an AstroStart HST5224 remote, you must putthe key in the ignition ... lamp) b, press and hold UNLOCK button, after 1 second key LED will flash once c, .... C. Turn the ignition to ON (Do NOT Start) then back to OFF. ... B.Immediately after letting go of the lock and unlock buttons, press the lock button by ..

Nov 24, 2015 | 2007 Jeep Wrangler Unlimited Rubicon 2...

2 Answers

Reprogram astrostart j5f tx2000


Get under the dash or where the unit is located.
You will see 8 or 9 dip switches on the unit with an LED beside them.
Turn switch 1 and 8 on.
Press and release the brake. (LED will flash)
Press and hold start button on remote. (LED will flash and parklights will flash once.
Turn switch 1 and 8 to off.
Press and release the brake (LED will flash once)
In future would be a good idea to supply vehicle details etc as can sometimes be a known condition , that saves time looking it up , good luck

Nov 18, 2014 | Cars & Trucks

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

1 Answer

Astrostart J5f Tx2000


You might want to post this question in a different section. This is the computer games section.

Jul 22, 2012 | Computers & Internet

1 Answer

Replace batteries on j5f- tx2000 astrostart - car only runs for 1 mintue - no manual so do not know how to reset


You have to put the key in the ignition and turn it clockwise to the run position inside of a minute after you open the door.

Nov 06, 2010 | GPS

1 Answer

Manual for ASTROFLEX j5f-tx1000 command start.


Try this one
http://www.astrostart.com/Support/Guides.aspx

Sep 18, 2010 | Nissan Quest Cars & Trucks

Not finding what you are looking for?
Vehicle Parts & Accessories Logo

Related Topics:

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vehicle Parts & Accessories Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...