Question about Televison & Video

Open Question

Need eeprom for 17MB12-2


Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 143 Answers

SOURCE: Fuse blown

ok well i would check for a open diode in the main ac to dc power supply then check all resistors that look lick they may be low ohms but high watt check to see if you might have a open pico fuse from primary power supply to the regulator check and see if you have stand by voltage this would be easily checked on the power off oan on button get back to me k

Posted on Nov 02, 2007

  • 1284 Answers

SOURCE: I need eeprom Konka or KLH KDT133UY. please.

I need a location number first so I can try to locate one for you.

Posted on Nov 05, 2009

  • 901 Answers

SOURCE: eeprom

You have to contact service center.

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My Hisense F46V89C, 46inch LCD TV no longer turns on, and only Clicks. Can anyone tell me which component is the EEPROM i'm supposed to replace on the main board?

Fault to its main board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Oct 29, 2015 | Hisense Televison & Video

1 Answer

Eeprom for Vizio M550NV

EEPROMs won't have no match. You should use the exact number. The loaded software cannot be changed; you know.

Jun 26, 2015 | Vizio M550NV 55 in LCD HDTV

2 Answers

The TV is freezing on the logo screen when the TV is turned on.

Corrupted firmware. A firmware update is necessary. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience.

May 07, 2015 | Vizio L32 32 in. LCD HDTV

2 Answers

Vizio E320VL has yellow light but wont turn on even with a new Power Supply

The power supply get's it "turn on" signal from the main board. It is very likely you have a faulty main board. Do you have electronics experience??

May 15, 2012 | Vizio E320VL 32 in. HD Ready LCD TV

1 Answer

Sharp aquos 42 inch lcd, too much red thro certain areas in the picture that should be dark. I have heard it needs eeprom reset how would i do this please, if anybody could help xx

Contact Sharp to see if it can be a "reset" issue and to see if this is a known problem in this model----more likely than reset would be a possible software upgrade but it depends on what actual issue is---maybe a bad board somewhere in the set.

Mar 25, 2012 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

Hello, i´m repairing an Acer AL2671W, the initial problem was the image with low bright even the bright and contrast controls are at 100%, later the tv sometimes get blocked and will not response to...

Eooow! Tough one. One of the main reasons why DLP Pictures are "weak" is not due to lamps or main board settings for the screen. The "weak" picture is due to the dirty (and I mean dirty!) mirrors BEHIND and BELOW the main screen, and possibly due to weak or dirty lamps and associated mirrors/lenses. Remove the "Front Screen" completely (not just the outer lens assembly) and check for internal dirt on associated mirrors inside the screen area. Disconnect any cables to the screen controls first (if any).

Aug 11, 2009 | Acer AL2671W 26 in. LCD Television

1 Answer

I have a 32 inch beko. bought second hand. been fine for 3 weeks but now when i switch it off it says turning off,please wait and last for 4.5 minutes!

Enter service menu using:
MENU, 9, 3, 0, 1
then goto EEPROM EDIT, and then EEPROM RESET, right arrow
to reset. Switch off. This should remove any eeprom corruption, causing the above fault

Jul 10, 2009 | Sharp Aquos LC-32G4U 32 in. HD-Ready LCD...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74198 Answers

Cindy Wells

Level 3 Expert

5124 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides