Cctv to video

Configure the network product View or change network settings
1. Type the IP address into the address line of a Web browser to open the embedded Web server. 2. Click the Networking tab to obtain network information. You can change settings as needed.
Manually configure IPv4 TCP/IP parameters from the control panel In addition to using the embedded Web server, you can also use the control-panel menus to set an IPv4 address, subnet mask, and default gateway. 1. Press Menu . 2. Press the down arrow to highlight CONFIGURE DEVICE, and then press OK. 3. Press the down arrow to highlight I/O, and then press OK. 4. Press the down arrow to highlight EMBEDDED JETDIRECT MENU, and then press OK. 5. Press the down arrow to highlight TCP/IP, and then press OK. 6. Press the down arrow to highlight IPV4 SETTINGS, and then press OK. 7. Press the down arrow to highlight MANUAL SETTINGS, and then press OK. 8. Press the down arrow to highlight IP ADDRESS, and then press OK. -or- Press the down arrow to highlight SUBNET MASK, and then press OK. -or- Press the down arrow to highlight DEFAULT GATEWAY, and then press OK. 9. Use the numeric keypad, or press the up arrow or the down arrow to increase or decrease the number for the first byte of the IP address, subnet mask, or default gateway. 10. Press OK to move to the next set of numbers. To move to the previous set of numbers, press the back arrow . 11. Repeat steps 9 and 10 until the IP address, subnet mask, or default gateway is complete, and then press OK to save the setting. 12. Press Menu to return to the Ready state.

The 55ux600u toshiba hdtv has a setting that needs to be changed with the wii in order to get color.
1. Click 'Menu' on the TV remote 2. Arrow over to 'Preferences' 3. Arrow down to 'AV Connection' 4. Click 'OK' 5. Arrow down to 'AV Input' 6. Change setting from 'ColorStream HD' to 'Video' by clicking the right arrow. 7. Hit the'Exit' button on the TV remote.
This will give you color for your Wii. You will have to change this setting back in order to view DVDs in color. :-)

1. Press [MODE] .
   
2. On the top line that says Normal Sci Eng use left arrow to move highlight from SCI to NORMAL an press [ENTER] to validate the setting.
   
3. After that, you must set the number of decimal digits: use down arrow to move cursor to second line. FLOAT 0 1 2 3 4 5 6 7 8 9
4. Use left or right arrow to highlight the number of digits you want. If you want 2 decimal digits, move cursor or 2 and press [ENTER]
5. Press [2nd][QUIT] to exist the [MODE] screen.
   

On remote control press 'Setup' button;
'DVD Video Setup' tab will be highlighted;
Using arrow keys around the 'Enter' key, press right arrow once to move to adjacent tab called 'HDD/DVD Setup';
Press down arrow once to move to 'HDD Setup' tab;
Press right arrow to move to 'Disc setup' tab;
Press down arrow to highlight 'Finalise' button;
Press 'Enter' and follow on screen prompts.

Sounds like your number lock maybe be on. It could also have a shortcut function option that is on. If not, have you spilled anything on it lately?

U have convergence board issues. Sometimes over time the solder joints on the board go bad or develop minute breaks. U might try removing the board and resoldering every thing you can get it. U can also consider baking the board in an oven at around 270 degrees for about 8 minutes to melt all of the connections on the bottom of board.
Then remove, allow to cool, cross your fingers and see what happens.

Bad chips...There are a ton of cheap fakes out there....Or bad resistor...

Projection TV sets have several common problems listed below.

Problem #1) Convergence

Symptoms:

• Screen Looks 3-D
• Colors wont align
• Screen may look distorted
• No Audio/Video - makes a chirping sound.

Example Photo:

Problem #2 CRT Fluid has clouded over.

Symptoms

• Dull Video, Washed out
• White/Bright looking video
• Halos around objects
• Red/Orange looking

Example Photo:


You can see more examples and find a fix here...

http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Take the closed caption (c.c) off on the remote and the black box will go away.

I love the way this works - if everything is plugged in properly, the remote control will be detected by the sensor and you should see an arrow on the screen that you can move by physically moving the remote. Use this to point the arrow to "English", then click "A", then move it again to "confirm" (...or is it "OK"?).

Disconnect power to the TV. The power interruption will allow you to reset the parental control password to the default password of 0000.

To change the password after disconnecting the power, do the following:

1. Press the Menu button on the remote.
2. Arrow up / down to SET LOCK CODE
The lock icom will appear
3. Arrow left / right to operate
4. Press 0 to access the lock code
5. The first digit will be highlighted.
Arrow left / right to select the number
Arrow up / down to move to the next digit
4. Continue to follow these directions for all 4 code numbers.
5. Arrow up / down to FINISH
6. Arrow left / right to save settings and exit.

The password has now been reset.