Question about Kenwood VR-405 Receiver

1 Answer

My remote control will not work

My remote control will not work even when i put new batteries in it.
Is there something i have to plug into the unit to make the remote work.
My unit is VR - 405

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TX light on remote control constantly blinking and display on set reverts to tape 1 all the time...please help...thank you...:)


Duh, the remote has a hot switch and it's always transmitting something. Blind it, hide it, pull the batteries before it kills them.

Try this advice:
http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641
"Dead" Remotes Can Be Saved
How to Re-Start Your "Dead" Remote Control
This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!
-----------------------------
Step 1- Pull the batteries out of the remote and leave them out until Step 4.
Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!
Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.
(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)
Step 4- Put the batteries back into the remote, being very careful to install them correctly. New batteries should be used if you're not sure about the old ones.
Step 5- Try the remote.
Special Note:
If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.
If it works, Great!
If not, it's time to call 1-800-Remotes or use this website to order a new remote.
Find new or replacement remotes:
http://remotes.com/store/codes_original.html
or eBay: search for "(model) remotes", check the 'include description' box. Usually cheaper than the vendors.

May 14, 2011 | Marantz SR-5000

2 Answers

Remote rc 1030


it must be your remote has been broken (just like my remote on tv) better to buy a new remote or buy a universal remote control.

thank you for using fixya
CHARCOIS

Oct 31, 2008 | Denon AVR-2807 Receiver

1 Answer

Remote control does not work


Try this advice:
http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641
"Dead" Remotes Can Be Saved
How to Re-Start Your "Dead" Remote Control
This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!
-----------------------------
Step 1- Pull the batteries out of the remote and leave them out until Step 4.
Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!
Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.
(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)
Step 4- Put the batteries back into the remote, being very careful to install them correctly.
New batteries should be used if you're not sure about the old ones.
Step 5- Try the remote.
Special Note:
If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.
If it works, Great!
If not, it's time to call 1-800-Remotes or use this website to order a new remote.
Find new or replacement remotes:
http://remotes.com/store/codes_original.html
or eBay: search for "(model) remotes", check the 'include description' box. Usually cheaper than the vendors.

Apr 23, 2011 | Kenwood Audio & Video Receivers

1 Answer

The remote functions intermittently. have replaced the batteries. if I fiddle with the remote for about 15 minutes it will function so of its functions are slow to respond


Try this advice:
http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641
"Dead" Remotes Can Be Saved
How to Re-Start Your "Dead" Remote Control
This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!
-----------------------------
Step 1- Pull the batteries out of the remote and leave them out until Step 4.
Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!
Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.
(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)
Step 4- Put the batteries back into the remote, being very careful to install them correctly.
New batteries should be used if you're not sure about the old ones.
Step 5- Try the remote.
Special Note:
If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.
If it works, Great!
If not, it's time to call 1-800-Remotes or use this website to order a new remote.
Find new or replacement remotes:
http://remotes.com/store/codes_original.html
or eBay: search for "(model) remotes", check the 'include description' box. Usually cheaper than the vendors.

Apr 23, 2011 | Audio & Video Receivers

1 Answer

Sony STR-DE697. Remote will not communicate with amp, has new batterys, amp is fine otherwise


Make sure the receiver's remote 'eye' is not exposed to high infrared energy from other sources, like the sun.

Try this advice:


http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641


"Dead" Remotes Can Be Saved

How to Re-Start Your "Dead" Remote Control

This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!

-----------------------------

Step 1- Pull the batteries out of the remote and leave them out until Step 4.


Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!


Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.


(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)


Step 4- Put the batteries back into the remote, being very careful to install them correctly.

New batteries should be used if you're not sure about the old ones.


Step 5- Try the remote.


Special Note:


If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.


If it works, Great!

If not, it's time to call 1-800-Remotes or use this website to order a new remote.


Find new or replacement remotes:


http://remotes.com/store/codes_original.html


or eBay: search for "(model) remotes", check the 'include description

Apr 06, 2011 | Sony STR-DE697 Receiver

1 Answer

The remote will not work replaced batt. with new ones clear line to sensor


Try this advice:


http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641


"Dead" Remotes Can Be Saved

How to Re-Start Your "Dead" Remote Control

This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!

-----------------------------

Step 1- Pull the batteries out of the remote and leave them out until Step 4.


Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!


Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.


(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)


Step 4- Put the batteries back into the remote, being very careful to install them correctly.

New batteries should be used if you're not sure about the old ones.


Step 5- Try the remote.


Special Note:


If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.


If it works, Great!

If not, it's time to call 1-800-Remotes or use this website to order a new remote.


Find new or replacement remotes:


http://remotes.com/store/codes_original.html


or eBay: search for "(model) remotes", check the 'include description

Apr 01, 2011 | Toshiba Audio & Video Receivers

1 Answer

Remote not working. tried the tin foil idea w/o success. can you repair or tell me where to replace it?


Try this advice:


http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641


"Dead" Remotes Can Be Saved

How to Re-Start Your "Dead" Remote Control

This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!

-----------------------------

Step 1- Pull the batteries out of the remote and leave them out until Step 4.


Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!


Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.


(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)


Step 4- Put the batteries back into the remote, being very careful to install them correctly.

New batteries should be used if you're not sure about the old ones.


Step 5- Try the remote.


Special Note:


If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.


If it works, Great!

If not, it's time to call 1-800-Remotes or use this website to order a new remote.


Find new or replacement remotes:


http://remotes.com/store/codes_original.html


or eBay: search for "(model) remotes", check the 'include description

Mar 28, 2011 | Audio & Video Receivers

1 Answer

The remote for my kenwood vr-407 receiver always chooses to work, and then randomly chooses not to work, and then chooses to work again. sometimes opening the battery cover and rotating the batteries a...


Try this advice:


http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12954406270641


"Dead" Remotes Can Be Saved

How to Re-Start Your "Dead" Remote Control

This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!

-----------------------------

Step 1- Pull the batteries out of the remote and leave them out until Step 4.


Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!


Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.


(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)


Step 4- Put the batteries back into the remote, being very careful to install them correctly.

New batteries should be used if you're not sure about the old ones.


Step 5- Try the remote.


Special Note:


If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.


If it works, Great!

If not, it's time to call 1-800-Remotes or use this website to order a new remote.


Find new or replacement remotes:


http://remotes.com/store/codes_original.html


or eBay: search for "(model) remotes", check the 'include description

Mar 22, 2011 | Kenwood VR-407 Receiver

1 Answer

Hi, I have a Pioneer XV-DV77 DVD/CD Tuner. My tuner does not work most of the time but occasionally it does after pressing different buttons on the remote control. Sometimes it works if I switch off...


I'd advise eliminating any intervening hardware until you resolve the problem.

What exactly isn't working that also goes through a VCR to a TV? How is it all connected, specifically?

"Different buttons". Can you be more specific? Perhaps you just have a remote control issue.

See this link:
http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12963989782821

"Dead" Remotes Can Be Saved How to Re-Start Your "Dead" Remote Control This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck!
Step 1- Pull the batteries out of the remote and leave them out until Step 4.
Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once!
Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2.
(When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!)
Step 4- Put the batteries back into the remote, being very careful to install them correctly.
New batteries should be used if you're not sure about the old ones.
Step 5- Try the remote.
Special Note:
If you have a digital camera, camcorder or camera phone you can test the remote to see if it is emitting a signal. Face the remote towards the lens of the digital unit until you can see the front of the remote. Depress any button on the remote. You should see a light (steady, blink or flashing) being emitted from the remote. If you do then the problem might not be the remote but the sensor on the unit.

If it works, Great!
If not, it's time to call 1-800-Remotes or use this website to order a new remote.

Jan 30, 2011 | Audio & Video Receivers

Not finding what you are looking for?
Kenwood VR-405 Receiver Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

ask_not

Level 1 Expert

28 Answers

Fbcgilly

Level 1 Expert

13 Answers

Are you a Kenwood Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...