Question about MTX JackHammer JH600 Car Audio Amplifier

1 Answer

Amp going into safe mode acts like its not getting enof power, power and ground are both 4 gage and hooked up corectly

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

Check the speaker wireing that it is not off somewhere ,or pinch.End shorting out. If all that is okay. It is not wired up properly to the sub or what ever speakers you have hooked up to it, Or you don,t have it set up (Poperly) They do not go into the protect mode For nothing,Unless you are trying to wire up your sub or (Speakers) To lower ohms then what it is stable for.If that is the case your lucky that it hasn,t went up in smoke yet,End that is not covered buy any manufacturs Warrenty,

Posted on Nov 04, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get amp out of safe mode


first check all connections, fuses and speaker wiring. Check to make sure that the amp is getting enough power to keep it running, meaning a piece of 4 to 8 gauge minimum wre from your battery to the amp. Make sure no wires are touching ground on the speaker outputs all the way to where they connect to the speakers. You can check this with a Ohm Meter to see if their is a direct short to ground. Or unhook all speakers and 1 by 1 touch them onto the amp to see if it cuts out. If the amp is going iinto protect mode without any speakers hooked up to iit (I have a bad keyboard sorry for the extra or missiing I's) and all other things I mentioned are OK then your amps bad and needs to be serviced. Hopefully It's just be a shorted speaker or wire.

Aug 07, 2013 | Jensen XA4100 Car Audio Amplifier

1 Answer

What gage power cable for this amp?


at least a 8gage and that for your ground if not better then that make sure you have it grounded right and to bare metal or else you amp will have cooling problems and most likely go into protect mode

hope this helps

Feb 26, 2011 | Diesel Audio NS-1000 Car Audio Amplifier

1 Answer

Fuel Gage is almost always bouncing a little in Why Is My Fuel Gage Needle Bouncing? It is almost always bouncing a little and in sink w/ some fluctuations in the headlights brightness. I replaced my fuel...


Your problem, as to my knowledge, seems to be more of a ground issue, or power supply issue. Check the grounds throughout your vehicle, including the ground for the fuel pump.

Jan 07, 2011 | GMC K1500 Cars & Trucks

1 Answer

Wish to run sm450v2 Mackie powered speakers thru a Peavey XR8600


The Peavey XR8600 is NOT just an amp, but a powered mixer.

To SAFELY use this with your powered speakers, connect those speakers to the MAIN and MONITOR outputs on the front of the unit with 1/4 inch INSTRUMENT rated cables (NOT speaker cables).

To safely leave the power amps in the XR8600 with no output loads, plug GROUNDING plugs into the POWER AMP 1 and 2 input jacks on the front. This will prevent the power amps in the XR8600 from running with no load which COULD damage them.

Make the grounding plugs from 1/4 inch mono plugs by jumpering the centr aand sleeve terminals of the plug.

Jul 09, 2010 | Peavey Audio Players & Recorders

2 Answers

Amplfier mtx rfl404 goes into safe mode when playing at load volume after 10 mins


you might need to turn the amp down and get some better wires to carry the load. when at lot of juice is being tranfered you need good wires to hold it

Mar 14, 2010 | MTX Thunder 801D Car Audio Amplifier

2 Answers

I have 1000 watt sony XPLOD amp and i just installed it today. with new monster cable&ground. the green light turns on& thumping goes for a little. i try to raise up just a little bit& after 2...


it isnt getting enough power and its tripping the internal switch on the amp and putting it in safe mode. either your wire isnt a high enough gauge. you might need a capacitor or you need bigger wire.

Jun 13, 2009 | Sony Xplod XM-554ZR Car Audio Amplifier

1 Answer

Amp staysin power safe mode


Check your ground wire and put your setting on your amp to low HP LP FULL also check the radio wires

Jun 03, 2009 | Cadence Z8000 Car Audio Amplifier

1 Answer

Rockford 800.2


what gage power wire are you running sounds like you need a smaller gage wire i have mine hooked up to a 4 gage wire and its working great

Oct 18, 2008 | Rockford Fosgate 800.2 Car Audio Amplifier

1 Answer

Cadence z1200 stays in Safe Mode!


If the subs are rmoved from the amp (wiring), does the amp still go into protection without them hooked up? If no, shorted sub, if it still des, unplug RCA's, does it still go into protection? Also check voltage. Make SURE you have greater than 12 volts AT THE AMP using amps ground to check the power AND remote wires. Hit me back wth an update.Those amps rock.

Larry T
Winona Lake, IN
http://www.cybersoundsaudio.com/cybersounds/vehiclepics.html

Sep 17, 2006 | Cadence Z8000 Car Audio Amplifier

Not finding what you are looking for?
MTX JackHammer JH600 Car Audio Amplifier Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top MTX Car Audio & Video Experts

hoyzee1

Level 2 Expert

150 Answers

yadayada
yadayada

Level 3 Expert

80339 Answers

RegWorts

Level 1 Expert

12 Answers

Are you a MTX Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...