Question about Jenn-Air JGS8850ADS Gas Kitchen Range

2 Answers

Jenn Air JGS8850ADS Range

For the 2nd time, I have an error code displayed on the front panel F8 (call service). LAst time they replaced the electtronic panel. Now, 13 months later, its bad again. Anyone have similar problems? Paid $1600 for the range and don't want to keep replacing electonics every couple years!

Posted by on

  • 11 more comments 
  • BrooklynJosh Nov 20, 2007

    Hi I have a Jenn Air JGS8850ADS Slide in Range with an F1-8 Error message on it. Any idea what the problem is and what I need to replace before Thanksgiving day? Thanks in advance.


  • ladysouth Dec 06, 2007

    We have the same f8 call serviceman message. Does any one know if this can be shut down without affecting the range itself?



  • fern54 Dec 06, 2007

    I have the same problem. I get the f1-8 error. I have had this range for 3 and half years and for the second time they will be replacing the electronic control unit. I just keep taking the Sear's extended warranty.
    Very sad. I bought Jenn-Air because I though it was good.

  • Anonymous Dec 07, 2007

    I have had this stove since 11/04. The exact same part has been replaced 11 times. I also bought Jenn-Air because I thought it was a decent brand. I am now fighting with the extended warranty company because the same part has been replaced 4 times in 1 year. Since it was new in 2004 I have never had an oven during the holiday season!

  • lisampls Dec 12, 2007

    Oh boy, we just got this error last night after using the broiler for the first time. I'm bummed to see others with the problem that hasn't gotten addressed.

  • frank parisi Dec 16, 2007

    yep have the same problem not happy at all if its not one thing its another i am so sick of this shit its almost like the kids toys they still make them with led

    in it and know one gives a shit...they all just want are money and they dont know how to make ppl happy after they buy mike holmes always say do it right...

  • tinkeringtom Dec 19, 2007

    f8 fault code ...continueous beeping after touching the cancel button..please help

  • oneFlake Mar 25, 2008

    We've had ours since Nov 05. It's had all the same problems that the others have had. It first went out at 4 months and is out now for the 4th or 5th time. It's worked aprox 19 months out of the 29 months we've owned it. It's always the control panel. Does anybodys elses start on it's own.

  • hayaz May 01, 2008



  • Geo333 Aug 02, 2008

    Control panel is dead. After shutting down and powering up displays:

    EE-214 M-214.

    Clock restarts at 12:00, cannot adjust anything.

    Where can I find error codes?

    Had 1-1/2 years.


  • Anonymous Oct 16, 2008

    I am replacing control panel for 4th time in 2 years. Oven turned on by itself- fire hazard. If fire I will own Maytag

  • 2007Jake Nov 19, 2008

    F1-8 code thrid electrical panel in 2 1/2 years! Stove is a lemon, the joke is the Maytag repair states the have no issues or reported problems with the product.

  • Anonymous Mar 10, 2009

    I have had the control panel replaced 5 times since purchased in 2006. 5th time today. This is defintley a lemon. Is ther any recourse ?



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Ee-214 m-214

Posted on May 30, 2009


This model is a lemon. Maytag knows and does not care. My panel has been replaced 8 times already. Stay away from Maytag.

Posted on May 25, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Duet. What does F8E1 code indicate needs to be done to restore operation?

Check out the Link and the info below.
Question: Front Load Washer - Error Code - F8 E1 or LO FL Answer Product Symptom:
Front Load Washer - Error Code - F8 E1 or LO FL

F8 E1 or LO FL Code in display:
No water detected entering washer after 13 minutes, the pressure switch input has not been detected.
If the washer has an F8 E1 error or LO FL error, the door will be locked, and the control will be unresponsive. The washer will start a drain routine which takes approximately 8 to 10 minutes, during which time the pump will run continuously. The control will not accept any input during this time. Please wait 10 minutes before trying to perform any functions.
Check the water supply:

Turn on the water. Check the household water supply to see if the hot and cold water faucets are turned on. Make sure to open both faucets completely for proper fill.

NOTE: Both Hot and Cold water must be supplied to the washer.

Whirlpool recommends that appliances be direct connected to the water supply for optimum machine performance.
If a "flood saver" device is being considered:
  • Check with the manufacturer of the device to ensure it will not affect the performance of the appliance.

  • Whirlpool has experienced that "flood safety" devices can interfere with the performance of the appliance. Whirlpool typically does not recommend these devices.
Two types of "flood-saver" devices, hoses and valves are illustrated below. anti%20flood%20hose%202.jpeg floodsafe%203.jpeg Whirlpool Duet Washer F8 Code Appliance Repair Forum

Jan 19, 2016 | Whirlpool Washing Machines



Service tool modeHow to access
1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.
Display of SOS History
SOS History (Number of LED blinking) indication. From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory shipment setting].POWER ON TIME/COUNT
Note : To display TIME/COUNT menu, highlight position, then press MUTE for (3sec).
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.Exit
1. Disconnect the AC cord from wall outlet.
Hotel mode
1. Purpose
Restrict a function for hotels.
2. Access command to the Hotel mode setup menu In order to display the Hotel mode setup menu, please enter the following command(within 2 second).
[TV] : Vol. [Down] + [REMOTE] : INPUT (3 times)
Then, the Hotel mode setup menu is displayed.
3. To exit the Hotel mode setup menu Disconnect AC power cord from wall outlet.
Troubleshooting Guide
Use the self-check function to test the unit.
1. Checking the IIC bus lines
2. Power LED Blinking timingCheck of the IIC bus linesHow to access
Self-check indication only:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
Self-check indication and forced to factory shipment setting:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
Disconnect the AC cord from wall outlet.
Power LED Blinking timing chart
1. Subject
Information of LED Flashing timing chart.
2. Contents
When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.



on Jun 30, 2015 | Panasonic Tc-50ps14 Tv Power Supply Board...

1 Answer

The control card is displaying error ch-01

PDF]SERVICE MANUAL R?410A Ductless Split System Air ...
421 01 9204 00 1/03/13. SERVICE MANUAL ... Consult local building codes and National Electrical Code. (NEC) for special ..... 18000 (5970-22350). Heating Capacity (Min. - Max). Btu/h. N/A ..... Error Messages Displayed Front Panel. S.

Oct 08, 2015 | LG 18000 BTU Dual Zone Mini-Split Heat...

1 Answer

Error code C2801 for Bizhub 750

When was the last time the developer was replaced in the developer unit? If has been replaced then you might have a bad ATDC (Automatic Toner Density Control) sensor Located at the rear of the drum and below. (Remove drum to see, has a white cover on it attached to a control board, needs cleaning,2nd replace. If the developer was replaced when it was done was a vacuum cleaner used? IF so the static electricity from the vacuum clear destroyed the sensor, NEVER USE a VACUUM cleaner to remove the developer. Also when the developer was replaced, was counter cleared to tell the copier developer was replaced, the copier use the counters to determine certain voltages for certain assemblies, if not image problems and codes can appear. Finally was the F8 run after the developer was installed before any prints or copies made? If not buy new developer and start over, counter is to be cleared first, then developer replaced, then F8 run.

May 21, 2014 | Konica Minolta Office Equipment & Supplies

1 Answer

My f&p gw611 Fills up but then wont wash.the 2nd

Most possibly be Error code 56,
Is common in 11 series machines & early series 12.
Is your machine beeping & showing a weird pattern of lights on the wash cycle, It is displaying an error code,
To read this error code you start at the red spin light & work to the left only add up the lights that are on. Red spin light = 1 2nd rinse light =2 1st rinse light =4 last wash light=8 4th wash light=16 3rd wash light=32 2nd wash light=64 1st wash light=128

Let me know your error code tour getting

Oct 20, 2013 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Error code showing 21:13 in designjet T620

There can be three solutions to this problem:
1. replace your service station
2. replace the print mech pca
3. replace the main pca
In that order. hopefully you can get this on the first repair (service station). this can become expensive. Let me know if this helps.

Aug 18, 2012 | HP Office Equipment & Supplies

1 Answer

Standby light blinks 13 times

13 blinks is backlight error.. can be 1 of 2 things, 1st bad inverter board (on left side panel looking from back) it has several plug ins to the panel as it supplies voltage to the backlights.2nd could be panel itself as backlights are built into it they can't be replaced. Inverter is probably around $200 +labor, panel= buy new tv... they are outrageously expensive. Good luck!

Apr 29, 2009 | Sony BRAVIA KDL-40S2010 40 in. LCD...

3 Answers

Hp photosmart 3200 all in one ink system failure

I know this sounds crazy but I did this and others have too, it worked. Hold down four buttons at the same time ( OK, Cancel, Black , Color ) and turn the power off. Note: I figured out how to hold the 4 keys down with one hand and push the on/off switch at the same time. Once you power the printer back up is will take a few minutes to go through maintenance. Then it will “hopefully” go back to normal. I did this 2x’s. HP gives you a procedure that doesn't work! They just want to make money off fixing it every 6 months. They are in the service, repair and “ink business” not printer manufacturing.

Nov 05, 2008 | HP PhotoSmart 1215 InkJet Printer

3 Answers

Error Codes 9-343

That means , second BTR is not in contact with transfer belt. Open front door and pull out paper transport and check that is everything OK with black roll and her assembly.Check sensors for dirt,and gears for damage.If You have used one ,replace it.

Nov 10, 2007 | Xerox DocuColor 12 Printer

Not finding what you are looking for?
Jenn-Air JGS8850ADS Gas Kitchen Range Logo

Related Topics:

930 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal De

Level 3 Expert

2694 Answers

Craig Butler
Craig Butler

Level 3 Expert

1723 Answers

Are you a Jenn-Air Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides