Question about Pool & Spa

2 Answers

Raypak FFL Fault Code

I am using a Raypak 406A Atmospheric Model Natural Gas. I am getting a FFL fault code and wont let the heater start. Any thought of what this is from and how to fix?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Clearing the ffl code

Posted on Aug 30, 2009


  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 22 Answers

The ffl is a false flame sensing when the heater is not in call for heat mode.

Posted on Feb 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i fix a model raypak 406A natural gas pool heater with a rollout switch open indicated?


replace but find out why either inproper gas supply which will soot up and overheat and burn that part or if gas is ok then see if wind caused it to roll out then add a wind stack

Aug 17, 2014 | Raypak 406A Digital ASME Natural Gas IID...

1 Answer

What could becausing my raypak model 406A natural gas pool heater is not working states roll out sw open


replace fusible link but see why it overheated wind or not enough gas pressure

Aug 17, 2014 | Raypak Pool & Spa

1 Answer

ROL keep displaying on my raypak rp 2100


check gas pressure if too low it will overheat replace rollout fusible link if it happens again you might need a vent stack

Jun 23, 2012 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

Hl1 hl2 code


high limits 1 and 2 open replace but check gas pressure first

Jun 10, 2012 | Raypak 406A Digital ASME Natural Gas IID...

1 Answer

Raypak 406A won't light


check wiring if 120 volt see wiring on inside of front panel if wiring ok switch black and white to see if it stays running

May 15, 2012 | Raypak 406A Digital ASME Natural Gas IID...

1 Answer

My Raypak 406A was out of propane. Now there is propane, but it wont ignite. Where can I find the manual reset button?


Sometimes when either a propane or natural gas system has air in the lines they will not work. To be safe I would recommend you call the Raypak technical support line at 800-947-2975 or800-627-2975 and they should be able to help you figure this issue out. I hope this helps.

Please vote on this answer. Thank you.

Aug 26, 2011 | RAYPAK R406A DIGITAL MODEL 406 wCUPR0...

2 Answers

Have an error code GVP


You didn't indicate what model heater you have, but here are some of the fault codes you might see. Could it have been GVO? You can download a manual for your exact model at www.raypak.com
BD1 Board failure
EEP Microprocessor error
FAN Blower pressure failure
FFL Flame sensing when pilot and gas
valves are closed
GVC Gas valve closed
GVO Gas valve open
HL1 High limit switch #1 open
HL2 High limit switch #2 open
IGN Ignition failure
ILO Ignition lockout - Propane units only
PRS Water pressure switch open
ROL Heat roll-out safety switch open
SNS Sensor failure, Water temp. below 36°F
or above 110°F
VNT Vent switch open

Aug 03, 2010 | Raypak Free Hydraulic Lift Gate Delivery -...

2 Answers

Opened the pool for the season but can't get heater to start


the most common problem is pilot light. IF you have electronic ignition, check the electronic starter. You also need to be sure you are getting gas to the unit.
David.

May 25, 2009 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

2 Answers

Raypak 2100 digital heater give fault code eol


ILO or ROL. There is no EOL.

ROL is a switch inside the lower left corner of the heater. Press the red button. ILO is a lockout. Power down and power up.

Nov 22, 2008 | Raypak Pool & Spa

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

1,012 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1224 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

3539 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...