Question about Canon PIXMA MP150 All-In-One InkJet Printer
Problem: Paper does not feed EXACT SAME PROBLEM FOR MOI Each time i try to print, the paper begins to feed through the printer, but seems to only be grabbing on the right side, so gets bunched each time!!! Help?
Awesome...fixed mine too. Mine was a little foam bumble bee that fell off of my daughters flower art work, which sat right above the printer.
Posted on Oct 21, 2012
Thanks guys for the help !!!... I looked deep deep inside, and I found a pendrive stuck between the rollers... (and a coin which I previously dug out) the pen srvie was really stuck in thee good....
Posted on Nov 12, 2011
Thank you so much! Found broken sun chip in mine. I'm blaming this on my three year old LOL
Posted on Jun 12, 2011
I found a key on a key ring eventually, It was fairly stuck in there I located it by watching where the edge of paper that failed to feed was damaged. The paper was bent bout an inch from the left hand side. Another indication was that envelopes were feeding ok when the left hand guide was holding them to the right. It was difficult to get that key out and I cut the piece of cardboard backing from a drawing pad to three inches wide and could not believe it when having pushed it in from the feed at the back when i pulled it out, with it came this key.
One thing sure, either my printer or the cork board above it will be moving.
Finally it is hard to believe this thing still works after the shaking, turning upside down, and jamming of card stack through the paper feed.
I finally forgive cannon for the camera that never worked again following a very careful trip to the beach. A grain of sand gave rise to a lens problem that cost as much as a new camera.
Posted on May 02, 2010
Thank you all very much. A few days ago I snapped the clip off a cheap plastic pen. Guess where it ended up :)
Posted on May 22, 2008
I had an identical problem. I found a flexible shatterproof 30cm plastic ruler is the best tool for the job. slid it in and out from left to right and out popped an after eight wrapper. As im the only one that eats them in my house i can't even blame the kids for this one.doh.
Printer now works perfectly..
Ian Clarke, Laindon, Essex
Posted on Apr 18, 2008
THANK YOU GUYS SOOO MUCH!!!!
Had this printer for 2 years now. After one month suffered from the exact same problem and just could not be bothered to do anything about it.
Tonight I decided to have a shot at fixing it and... ALLELUIA!
Tried shoving card through the printer and POP... out comes a BB gun pellet!!! My prayer came true. I finally got it fixed. One of the best days of my life.
Posted on Apr 10, 2008
I once had a similar problem a few months ago and I tried EVERYTHING I could do (Without shaking the printer, I was scared to do that) nothing worked, till I actually got up on a chair and looked into my printer (It is up on a rise above my computer) and there was a push pin sitting in the feeder opening! (Remove pushpin = then it was fine)
Then it started doing it AGAIN yesterday at a time when I really needed my printer, and this time there was no obvious pushpin or any obvious obstruction. I read all the stories here and thought *WOW they had things that far in there?!" So I tried harder and FINALLY after opening the back panel I saw with a flashlight there was a FROOTLOOP (I don't even HAVE any frootloops in my dorm! XD) jammed in the right side inside it! With a chopstick I was able to get it out and now it's fine again. OMG.
But yea, things like to get stuck in printers I guess. XD
Posted on Apr 02, 2008
Thank you! Pushed a piece of card through and out came a false nail.
Posted on Mar 16, 2008
Yah the paper feed and jam on the right side only was really getting to me too. The first time I thought it worked itself out. But this time after much suffering I checked this site and found that it maybe a good idea to check that something maybe stuck inside. I shook it, gave it to my husband to shake it, did everything but throw it down and stomp on it. Was starting to think that it was simply broken and bin-ready when I peered inside as far as I could. That's when I saw it. A little gift left by my 20month old wedged as far inside as it could possibly go. Must have come lose from the shaking. Finally got it out and the printer is working as good as new. My expert solution to fix printer? Get big fat pencil out of said printer.
Posted on Jan 22, 2008
Before you turn the printer upside down and shake you had better take out the ink cartridges.
Posted on Nov 30, 2007
IT WORKED!!!!!!!!!!!!!! THANK YOU!!!!!!!!!!!!!!!!!!!!!!!!!
Posted on Nov 28, 2007
Thank you very much. Shaking, turn it upside done, force thick paper into the printer. And we found a magnet from the whiteboard above the printer.
Posted on Oct 20, 2007
Thank you so much for the solution.
I pushed a sheet of cardboard through the printer and found a piece of a... felt-tip pen >.<
Never letting little kids in my room again, relatives or not...
Posted on Oct 18, 2007
LOL !!! ... It works, mine is fixed too !!!
Man, you should setup a tech service center for printer troubleshooting.
Turn it upside down ... shake it .... force paper down into the feeder .... feed cardboard into printer .... do a bit of vacuuming .... and viola ... presto .... it works. Brilliant.
I couldn't believe what the solution was to this problem until i tried it myself.
Posted on Oct 14, 2007
I LOVE YOU! Thank you sooooo much! I was just on the point of going out to buy another printer, but this worked brilliantly! (embarrasingly enough mine happened to be jammed by a stray sweet wrapper, so thats the last time i put anything on top of it..) Again, thank you!
Posted on Jul 25, 2007
Putting a thicker paper through the 3rd time pulled out the object that was causing my miss feed...a foam flying disk. This worked on my Canon i860!
Posted on Jun 29, 2007
From godfree who oginally asked. thank you mate thank you thank you as well
Posted on May 23, 2007
Thank you very much creativeguy, my kids are very appreciative for this solution and it worked...thank you thank you thank you
Posted on May 23, 2007
I've had this error for the last 2 months and periodically tried to fix it. - I finally read a suggestion to try to push something thicker than a plain sheet of paper through. I cut a side of a manilla folder into a 8.5"x11" and let the printer try to grab it during a copy. After doing it's normal "grab the right side until it's skewed and stop", I continued to try to push it through. I wasn't able to push it to the printing area, but I saw that a piece of something (not much bigger than a bread crumb) came out of the feeder into the interior print area. - I tried another copy, and it was very slightly improved but still skewing and jamming the paper. Suggest unplugging it before performing this...I then lifted the interior piece of plastic (white color for my Pixma MP 150 - which would be located above the paper as it was fed into the print area) slightly to allow any jammed items to come through. Out comes small pieces and then a larger piece of cracker (about the size of 1/4 a cheez-it). Ok I feel dumb, but I'm glad I found something. I picked out the crumbs and did a careful vacuum in the interior and exterior paper feed. Slight warning: The foam bottom below the ink is not secured and will get sucked up by the hose. And note, that I did try vacuuming the intake and interior previously with no improvement. The nozzle on my vacuum is too large to get into the bottom of the exterior intake. - For good measure, I also picked up the printer and turned it upside down and shook vigorously in a couple angles. I saw a couple more small crumbs come out. - My printer is now feeding the paper correctly and successfully made a copy/print.
Posted on May 18, 2007
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
gears below the paper feeding tray are damaged or some dust particle have blocked the gears try to clean it by blowing the dust use normal greece (oily substance) between the gears so that they can move frequently to pull the paper, and if the gears are damaged you have to change the gears.
Posted on Aug 08, 2008
Tips for a great answer:
May 17, 2010 | Lexmark X8350 InkJet Printer
Jul 02, 2008 | Office Equipment & Supplies
Oct 31, 2007 | Epson Stylus C86 InkJet Printer
Jun 21, 2009 | Canon PIXMA MP190 All-In-One InkJet...
Apr 21, 2009 | HP Hewlett Packard Officejet Pro L7680...
Aug 03, 2008 | Canon PIXMA MP160 All-In-One InkJet...
Jun 15, 2008 | Epson Stylus CX7800 All-In-One InkJet...
Oct 03, 2006 | Lexmark JetPrinter Z11 InkJet Color...
Jul 16, 2014 | Canon PIXMA MP150 All-In-One InkJet...
1,300 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: