Question about Mitsubishi WS-55315 55" Rear Projection HDTV-Ready Television

1 Answer

I think its the convergence box, tv is flikering and distorted.-

Posted by on

  • 1 more comment 
  • spridal2andy Jan 05, 2009

    No matter what video input, its doing the same thing.



    Lets just say its not flickering, I seen some flickering on youtuve and it looks like the tv is going, on off on off on off on off, which my tv is not. Its just distorting, changing for distorted, to really distorted, to back to normal, to distorted again, etc...

  • spridal2andy Jan 05, 2009

    Yes even when menu its up, it just seems to be apart of the whole mess, :P

  • gscrivner7 May 11, 2010

    Can you bring up the tv's customer menu and is it distorted?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 3,459 Answers

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on - TV may also make a chirping noise.
Here are some photos of convergence problems.

I think its the convergence - 49abec3.jpg
f0add3d.jpg


Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com

Posted on May 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace my convergance chip


contact parts distributors who sell convergence kits for your model.
Order instruction DVD.

Jun 03, 2010 | Televison & Video

1 Answer

Not able to flash focus or use manuel converence i think i need a convergence kit where can i purchase this kit


You probably need to get a Sony TV Convergence Kit for your model. More information can be found using the link below.

Convergence Symptoms:
  • Screen Looks Distorted/3D
  • Colors wont align
  • Screen may look distorted
  • No Audio/Video - makes a chirping sound.
You can see some examples and find a fix here...

bb0cf99.pnghttp://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Feb 09, 2010 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

Color distortion in an Akai ( Cheaper model Rear Projection tv) I


Ur convergence is dead.Try Tv repair World.com.
Buy a whole convergence board replaced it.

Jan 01, 2010 | Akai PT4799HD Rear Projection Television

1 Answer

Screen Distorted


Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on - TV may also make a chirping noise.
Here are some photos of convergence problems.

49abec3.jpg
f0add3d.jpg


Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

93a1209.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com

May 18, 2009 | Apex Digital GB5108 51" Rear Projection...

2 Answers

Concaved distorted picture in 1080 Mitsubishi 65" TV.


This is a convergence rpoblem that is either bad connections on the pins of the convergence ICs or defective ICs. If you can solder and are comfortable working inside TVs where there are potentially dangerous high voltages, let me know and I'll provide additional details and instructions for fixing this yourself.

Dan

Dec 11, 2008 | Mitsubishi WS-55807 TV

1 Answer

PHILIPS 60PW936317 - COLORS GOT DISTORTED AS I WAS WATCHING TV


Your convergence chips and convergence resistors are going bad. When they fail the screen colors will look distorted/3d looking.  Another symptom is one or more colors can't be converged using the convergence menu. You can purchase the parts over the internet. Just make sure you get Sanyo brand convergence chips and the correct flame proof resistors. You can also check the site www.TvRepairKits.com. They are working on a complete kit for this model.

Nov 12, 2008 | Philips 60PP9202 60" Rear Projection...

1 Answer

Distorted Picture


Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on - TV may also make a chirping noise.
Here are some photos of convergence problems.

49abec3.jpg
f0add3d.jpg


Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

93a1209.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com

Aug 02, 2008 | Toshiba 65HDX82 65" Rear Projection...

1 Answer

Picture distorted and blurry with color


bad convergence amp ic
http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
Sony Convergence
http://www.techlore.com/blog/entry/19694/Sony-Convergence-Repair-My-Sony-TV-has-a-distorted-picture-/
http://www.techlore.com/article/19631/Sony-Convergence-Procedure/

Jan 28, 2008 | Mitsubishi WT-46809 46" Rear Projection...

2 Answers

Kp-57ws500 sony projection tv convergence problem


Sony convergence problems
http://www.techlore.com/blog/entry/19694/Sony-Convergence-Repair-My-Sony-TV-has-a-distorted-picture-/

http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm
http://cmpalmer.blogspot.com/2006/11/fixing-my-own-tv-part-ii.html
Sony Convergence
http://www.techlore.com/blog/entry/19694/Sony-Convergence-Repair-My-Sony-TV-has-a-distorted-picture-/
http://www.techlore.com/article/19631/Sony-Convergence-Procedure/
look for the board that has heavy heat sinks on them the ic will be stk392-XXX
no experience in soldering i would send the board into ptscorp.com and have them repair it.

Jan 22, 2008 | Sony KP-41T65 41" Rear Projection...

Not finding what you are looking for?
Mitsubishi WS-55315 55" Rear Projection HDTV-Ready Television Logo

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

72670 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...