Question about Konica Minolta Office Equipment & Supplies

2 Answers

Error code c1144

Biz hub c654 queues jobs, never prints

Posted by Anonymous on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 10 Answers

Code 1144 is a finisher code , the middle arm in tray 2 of the stacker is usually stuck and needs to be pushed forward , then try the trouble reset by holding down reset while powering on , then touch trouble reset on the touch screen , power off and back on . You should be set

Posted on Dec 14, 2017

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have 5 biz hub 654s. There is no "utility" hardware button. Instead, open the front cover (marked "biz hub 654") - switch off the main power - white switch in an orange rectangle. Wait 30 secs. Flip back on- then QUICKLY close the door while holding down the yellow RESET button. "Trouble reset" appears - tap it - OK appears below it. Use main power to power down. Wait 30 seconds. Power back up. Works every time.

Posted on Oct 30, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

taminol
  • 62 Answers

SOURCE: Biz Hub C250 - code error C2551

Ahhh, you must be the same Macdaniel I emailed for clarification a short while ago.
C2551 relates to the Cyan imaging unit, the machine thinks the toner level inside the Cyan imaging unit is low.
Opening and shutting the main front door is the reset procedure. However if this doesn't work you should try the following
Remove the Cyan imaging unit, give it a bit of a shake and then refit.
Experience tells me that the above only works on occasion and you will probably require a new imaging unit. They are available for around £250.
Please be aware that the fault could also be down to a circuit board being defective, but this is less common.
Regards
Taminol

Posted on May 26, 2009

SOURCE: Biz Hub c250 gives error code 3452

C3452: Pressure Heater Trouble.
Try to reset it like this:
Shut down from the main power switch (the one behind the front cover).
Keep pressed the Utility/Counter button.
Power on while the button is kept pushed.
Release the 'Utility/Counter' button only when you see the 'Trouble Reset' button on the touch screen.
Touch the 'Trouble Reset' button, a small ok should pop up underneath.
Power off, wait for a few seconds and then power on.

Posted on Aug 23, 2009

  • 158 Answers

SOURCE: konica minolta biz hub C250 need to reset admin code URGENT

you cannot overide the administrator password on the konicas the default password is 12345678 try that

Posted on Oct 31, 2009

  • 44 Answers

SOURCE: bizhub 250. error c2152

Check and make sure there are no jams by the fuser ie: bits of paper in the paper path.

Posted on Nov 29, 2009

shadiabed
  • 72 Answers

SOURCE: Won't print, job remain in queueey

check the data cable or change the usb port if this fail please try to change the cable

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code f124 kyocera 8001


most f codes are print job related delete all your jobs from print queue

Jan 08, 2018 | Kyocera Office Equipment & Supplies

1 Answer

How to fix trouble code 0910


Unrecoverable error (The count is made by C-5402.)
An abnormal operation accurs when an interupt copy is made (copy print job 1). Estmated defective par Overall control board (OACB).

Oct 15, 2014 | Konica Minolta Office Equipment & Supplies

1 Answer

There is an error code on my HP LaserJet P3015 which reads 49.4C02 ERROR


HP LJ P3015 with 49.4c02 error - tried lots of things in the end went into printer driver right clicked and then clicked troubleshoot - windows came up with a fix dont know if it is permanent - troubleshooter said a print job was deleted from the print queue. Presume the printer tries to print the problem job in the queue each time it is switched on.

Oct 10, 2013 | HP Laserjet P3015X Printer

1 Answer

Konica Minolta biz hub c550 error code c-EEE3 Help please


To reset the malfunction code press follow keys:
Turn OFF the copier,press and hold pressed the Utility key and turn ON the copier.Wait will apaire the Trouble reset message on the display and release the Utility key.Touch the message and turn OFF the copier.Wait 1 minutes and turn ON.Good luck.

Mar 21, 2013 | Konica Minolta Office Equipment & Supplies

1 Answer

How to clear error code 49.4c18 on HP laserjet 4250


any 49.xxxx codes are related to firmware crash.
the probable cause is a corrupt file in the print queue. remove the printer from the network then after network is disconnected - cycle the power on the machine ( switch off then wait 10 seconds switch back on)
the 49 error will probably clear . if so Clear All print jobs in Print queue on the computerr workstation. then reconnect printer and away you go!
if however the error remains then you will need to Upgrade the firmware or replace the firmare chip/formatter ( unlikely I've only ever replaced one out of thousands of calls for this fault)

Nov 04, 2012 | HP LaserJet 4250n Printer

2 Answers

KM Bizhub Pro 920 gets an error: SC21-04.


Wire cleaning problem, there are several motors in the copier that have the job of cleaning Very HighVoltage Drum Charge Wires and Image Transfer and seperation High Voltage wire The wires have a corona (Not beer:)) form on them and need to be cleaned.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Mar 25, 2009 | Konica Minolta Office Equipment & Supplies

1 Answer

Printer Won't Print


Step one: Restart the computer
Click Start and click Shut Down.
Click Restart or select Restart from the menu. Click OK.
After the computer restarts, double-click the Printer icon in the system tray located at the bottom, right of the computer. The print queue opens. If no documents appear in the print queue, the issue is resolved.
If the issue continues, proceed to the next step.
Step two: Check the product cable, Disconnect the USB cable from the product and from the computer.
Wait 5 to 6 seconds. Reconnect the USB cable to the product and computer.
(NOTE: The product must be connected directly to the computer using a USB cable or a powered USB hub. If the product is connected to the computer through a non-powered USB hub, or if the type of hub is unknown, connect the product directly to the computer) after the product is connected to the computer, the product should start printing the jobs in the print queue. If the issue continues, proceed to the next step.
Step three: Determine whether the product is paused or offline, Click Start and click Printers and Faxes. The Printers and Faxes window appears. In the Printers and Faxes window, right-click the product icon and click Open. The Printers folder opens. On the menu bar, click Printer. Make sure that the Pause Printing and Use Printer Offline options are not selected. If a check mark appears next to either option, click to remove it. If the menu includes Use Printer Online, click that option.
If neither Pause Printing nor Use Printer Offline is selected, press Esc to leave the menu without making changes.
If the issue continues, proceed to the next step.
Step four: Stop the print queue, Double-click Macintosh HD, Double-click the Application/Utilities folder.
Open the Print Setup Utility folder; Double-click the appropriate product in the product list to open the print queue.
Click Start Jobs. (NOTE: If the queue was accidentally stopped, the print job will resume automatically. If the issue continues, proceed to the next step)
Step five: Delete the print jobs, Double-click Macintosh HD, Double-click the Application/Utilities folder.
Open the Print Setup Utility folder, Click a print job and click the Delete icon. Repeat the steps for all the jobs in the print queue, Click Start Jobs, Double-click the appropriate product in the product list to open the print queue.
When the print queue is empty, click Start Jobs. Try the print job again. If the issue continues, proceed to the next step.
Step six: Remove and re-add the product to the printer list, Double-click Macintosh HD, Double-click the Application/Utilities folder, Open the Print Setup Utility folder, Select the appropriate product.
Click the red X to delete the product from the computer, Disconnect the USB or Ethernet cable from the product.
Close all open windows and restart the computer, after the computer is restarted, double-click Macintosh HD.
Double-click the Application/Utilities folder, Open the Print Setup Utility folder, and Reconnect the USB or Ethernet cable to the product. If the product is not automatically added, click Add. Select the product to add and click the Add button. After a few seconds, the product appears in the printer list. Try the print job again.

Jul 18, 2008 | HP DeskJet 5150 InkJet Printer

1 Answer

Error in Print Jobs in the Queue


The use of a Print Buffer will help, the problem happens when there is a buffer overflow. Reboot the printer and let the print queue to resume will fix it every time, a print buffer will help with the overflow, try get one with a fair bit of RAM

Jul 15, 2008 | Zebra Z4M Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

3,073 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6763 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Clive
Clive

Level 3 Expert

4345 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...