Question about Whirlpool Washing Machines

1 Answer

Washer stops in middle of cycle and flashes error code f 05

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Whirlpool Master
  • 9,472 Answers

F-5 Water temp sensor failure
If during the water heating step in the wash cycle, the water
temperature sensor (NTC) value is out of range, the "F/05" error code
will be displayed. Possible cause/proceedure:
1. Unplug washer or disconnect power.
2. Check the water temperature sensor.
Check connections to the water temperature sensor.
3. Check resistance of heating element, if present on this
model. (abnormal = infinity)

Posted on Nov 02, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jsrock516
  • 5911 Answers

SOURCE: Whirlpool Duet Washer

F11 is a serial communications error. This is a symptom of an electronic control board starting to go bad. As defined by the technical information provided by Whirlpool, the error could also be caused by a loose or broken wire connector and/or the central control unit (CCU) (front panel). I would double check all your wire connections leading to the control board and CCU, first. Don't be surprised, however, if the problem persists and you eventually have to replace the electronic control board. To check, follow these steps: 1. Unplug washer. 2. Remove the three screws along the top of the washer in the rear that holds the top panel on. 3. Once the screws are removed the top should slide back then lift up. 4. The electronic control board is gray (or white) in color and located in the rear of the washer. It's impossible to miss. Double check all the connections ONE AT A TIME. 5. Double check the wire harness connections leading to the front panel as well. I hope this resolves your problem, but experience has proven that this is usually an Electronic Control Board failure. It could actually be a combination of the CCU as well. The part numbers are as follows: Electronic Control Board: 959503 Central Control Unit: 1025824 Both boards cost about $150 each. Let me know if this helps you.

Posted on Sep 03, 2007

  • 2 Answers

SOURCE: L5 error code

Could be a "Lid Switch (LS)" error.

Posted on Dec 27, 2007

  • 1 Answer

SOURCE: Maytag Neptune Error COde "nd"

This is now the 3rd time this has happened. The 1st 2 times it cost me ~$100 to have a technician come in and fix.

This time, I did it easily. For my Maytag Neptune washer, I removed the back panel (2 screws). On the bottom tray is the water discharge pump. On the output side of the pump there is a small cavity under the rubber flapper where a nickle fits perfectly. I removed the nickle, reattached the output drain line. started it up ...

and viola! the problem solved.

Posted on Jun 28, 2009

RixsFixes
  • 2200 Answers

SOURCE: my kenmore front load washer keeps showing a F--20

Hi

The F20 error on this machine indicates that there is no or very little water coming into the machine. This means that the pressure switch is not being activated after a while and the error is then thrown up.

See this excellent FixYa link for a complete breakdown of the problem and how to troubleshoot and then solve it.

Acknowledgement jsrock516 for this excellent breakdown of the problem

http://www.fixya.com/support/r1491905-f20_error_code_whirlpool_duet_kenmore

Please do rate my answer. Many Thanks.

Posted on Aug 27, 2009

  • 299 Answers

SOURCE: F1 error code on Kenmore Oasis He

After getting the F1 error on my model 110.27086601 and looking at other posts here & elsewhere, I made one call to the "Product Resolution Center" at 800-847-9083 on 4/9/10. They answered quickly, looked up the model & serial number I gave them (begins with CT18) and confirmed that the unit is covered under the "upgrade plan" (as opposed to calling it a recall). They are sending the part directly to me today and they scheduled a Sears tech to come install it in 10 days (or less if the part arrives sooner). The part, shipping and service call are free. The whole call took less than 5 minutes and was no more difficult than ordering a pizza. The agent was polite, professional and a pleasure to deal with.
I'm pleased that 2 years after the warranty expired they are providing this repair free of charge and without any hassle.
To those who have had problems when calling or who will be calling, may I offer this tidbit for dealing with any customer service contact? Be polite and businesslike. The agent on the other end doesn't need to hear about "how disappointed you are, blah, blah" or that you've "been a loyal customer for 84 years" and you've "never had a problem like this" or any other editorial commentary - just be friendly, and say something like " Hi, I have an Oasis washer with the F1 problem and I understand that there's a recall covering this." That's exactly what I said and the agent efficiently handled everything from there.
Remember, the agent gets measured on the number of calls they complete so they just want to take care of you as quickly as possible. Help them by just simply stating the problem and just answering their questions with just the information requested. They are not there to listen to people whine - they've heard everything you have to say a thousand times and they will appreciate your brevity and no nonsense demeanor. Make it easy for them and they'll make it easy for you. Do your venting here if you must.

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mass 6 Bosch washing machine is locked up and was blinking in red light letter F what do I do


"Sd" - (Excess suds)
F8 followed by E1 - (water supply error)
F9 followed by E1 - (drain pump system error)
F5 followed by E2 - (door will not lock)
F7 followed by E1 - (motor drive error)
"rL" - (remove load)
Washer making error beeps - Door has not been opened and closed for at least 3 cycles
Washer beeps when HOLD TO START is touched - Door not closed
F# E# code other than as described above appears in display - System Code Error
"nt" (interrupted) - Cycle was paused or cancelled
Clean Washer LED flashing at end of wash cycle - The washer has run 30 wash cycles and is indicating a reminder to run the Clean Washer cycle https://removeandreplace.com/2015/05/05/washing-machine-error-codes-front-and-top-load

Sep 21, 2017 | Bosch Washing Machines

1 Answer

Machine stopped in middle of cycle ,wash flashing something on screen, tried to restart wont't run water could it be out of level for it not to run water


It's probably flashing an error code. Write down the code and look it up in the owners manual or online to find out what the issue is.

Aug 17, 2014 | Samsung WF328AA Front Load Washer

1 Answer

My whirpool locked light keeps flashing and wont wash


Hi


The light is flashing due to the door lock error. The door lock is activated as the machine experienced an error or was stopped in middle of a cycle. Or the door was being pulled while the machine was running a cycle. Try unplugging your washer and restart the washer to check if you are still getting the same blinking light. If error is still not resolved then start the rinse/spin cycle & stop the cycle, now press and hold the cancel button for 5-10 seconds. However, if you are still not able to get the door open then you'll need to open the door manually by disassembling the washer.
Hope this helps... Please post back for any further assistance.


Daniel

Apr 18, 2011 | Washing Machines

2 Answers

Amana nfw7200 washer stopped in middle of cycle and is flashing ''nd''


is it full of water? if so there is a drain problem and may have to clean out the pump

Aug 23, 2009 | Maytag NFW7200TW Front Load Washer

1 Answer

Motor error with out error code.


use tech sheet to follow test routine. C:05 is Heater test. some steps take time. during normal operation if timer display flashes, may be indication of standby/pause. Door lock sw may be bad(intermittant)

Apr 22, 2009 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Error code F05 after the start of wash cycle


F05 is a water temp sensor error ,could be a bad heating element, or the temp sensor may be faulty, try checking the connection's to the temp sensor and heating element, also check the element relay.

Apr 20, 2009 | Whirlpool GHW9100L Front Load Washer

1 Answer

Machineflashinf f-05


F05 machine means "Pressure switch jammed"

Try first cutting power to the machine for two minutes, if that reset the code, then the problem was temporary.

If not :

Check if the machine drained, or if water is not being drained.

If drain system works .take off the the lid , locate the switch, it must have a small hose attached.
Remove the rubber hose attached to it, and unlock it by blowing into the hose.

If the water does not drain, this will also cause the pressure switch error.
In this case check the drain hose , and the drain pump.

Finally, ta faulty timer control board can cause the error, you test the control PCB if lid switch and drain system are OK.

Mar 09, 2009 | Hotpoint Ultima WD72 Front Load...

1 Answer

Kenmore HE3 stops in middle of cycle, flashes F-11.


F/11 Serial Communication Error
Communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.
  • Check Wire Harness connectors to the MCU, the motor, and Central Control Unit (CCU)
  • Check the Drive system for any worn or failed components
  • Check MCU
  • Check CCU
  • Check Motor
  • Check Wire Harness

Dec 08, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

F-05 flashes


The following link expains the "F05" error code:

http://www.fixya.com/support/r629462-f05_error_code_whirlpool_duet_kenmore

Check to see if the connector is still plugged into the heat sensor, first. I have seen where the connector has come loose and caused this error code. If not, take the resistance readings as recommended. I hope this helps you.

Jul 26, 2008 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

"F" error code in WTW6600SG1 Cabrio Washer


I don't have a solition and am looking for one my duet whirlpool keeps coming up code F

Jul 07, 2008 | Whirlpool WTW6600SW Top Load

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2254 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...