Question about Zanussi FJD1466W Front Load Washer

1 Answer

E10 Fault Keep getting an E10 fault but water flows on other parts of wash

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Hello E10 = Problems during water filling phase ? washing (Machine tries to fill for 10 min without reaching the level) Checks to do: Is there one of the tree valves that is not working? NO, Verify that tap and hoses are letting the water coming in. (tap open, hoses connected and not kinked) Is the wiring OK? (Measure the 3,8 K Ω of the valve from the cable Main board side: - between J6-1 and J6-5 wash valve; - between J6-2 and J6-4 prewash valve; -between J6-3 and J6-7 hot or bleach valve. if NO Replace the cable. Change the main Board Regards David Marsh

Posted on Jul 18, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ultima1000, wm 71 says error 10 sometimes and error 11 mid way thru a cycle. The pipes are fine and water is on what could be the problem?


E10 No cold fill detected - washing machine does not fill
  • Check mains water pressure
  • Check inlet hoses for kinks
  • Check inlet filter
  • Check water inlet valve
  • Pressure switch fault
  • Wiring fault
E11 Not hot fill detected - washing machine does not fill
  • Check mains water pressure
  • Check inlet hoses for kinks
  • Check inlet filter
  • Check water inlet valve
  • Pressure switch fault
  • Wiring fault

Apr 11, 2016 | Washing Machines

1 Answer

Washer stops shortly after startup with error code E10. We have to keep restarting it about 5 times before it will engage. Help.


Hello Christina Steppi - Typically error code E10 indicates that the unit takes too long to fill with water. Is the incoming water flow normal? If it is not, the unit could possibly have a faulty pressure switch, inlet valve assembly or main control board. I would strongly recommend consulting a professional to narrow down the precise issue before investing in parts that may or may not be the root cause. You can often locate a qualified tech through the manufacturer website.

Mar 08, 2013 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

My washing machine comes up with error code 4e i have changed the solenoid valve and cleared any possible blockage water is flowing in to the machine but still getting the same error code if i chose the...


Your machine has a fault with the water level contoller switch - pressure switch that activates when water reaches the level set . So check the water level controller and test. If not the fault can be with the program controller unit.
Please check this link for parts identification.

http://www.espares.co.uk/advice/washing-machines/a/7/40/identifying-washing-machine-parts.html

Sep 17, 2011 | Samsung Washing Machines

1 Answer

Water won't drain


Do the diagnostic test:
SHU 53 MODELS

To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show “88′ when REGULAR WASH button is pressed and “8h” when Delay Start button is pressed.
To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4).
0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
1 = Aqua Sensor (“Sensotronic”) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), display will show fault code “4′ and unit will continually fill and drain where testing won’t be completed. If flow switch (e5) has failed (opened), display will show “0′, water won’t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code “8′ immediately and testing will end shortly after water has started circulating.
---------
The dishwasher not draining is most probably faulty drain pump or drain hose is got bit loose.It has to be checked and confirmed
.You can get required parts from www.repairclinic.com
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Aug 27, 2010 | Bosch 24 in. SHU53 Built-in Dishwasher

1 Answer

It has a E10 fault code now it stops every 2 min beeping and it not pulling in enough water or spinning right can anyone help pls???


E10 means that there is a problem with water inlet. If the control board does not detect required water level after a certain time after opening inlet valve, then you will get F10.

Check that the inlet hose is not kinked and that there is pressure in there.

Try tripping the circuit breaker for ten minutes to reset the timer board.

If you still get E10, then you usually need to replace the triple inlet water valve connected to water hose. Usually the valve solenoid has gone.

The solenoid can be tested using a multimeter set at Rx1. If solenoid is good it will return about 4 KOhms, if not it will return infinity.

Regards.

G.

Nov 27, 2009 | Zanussi FJD1666W Front Load Washer

1 Answer

E10 PROPLEM AEG


Hi,
Your Machine manual is HERE

E10 is an inlet fault.
Check the water valve is turned on. If you are only getting a dribble of water in, then clean the inline filter at the hose inlet.
If no sound of inlet water - replace inlet valve (available as a spare from online stores)

Sep 30, 2009 | AEG Lavamat 16810 Front Load Washer/Dryer

4 Answers

E10 code on a zanussi jet system washer


Is it a washer-dryer? E10 relates to a fault with the inlet valve.....usually the valve itself going open circuit.

Feb 26, 2009 | Zanussi WJS1265W Front Load Washer/Dryer

1 Answer

EFO, E10 error Message


Frigidaire, Zanussi, AEG, & More....

EFO = Filter Blocked (low flow) and it is accessible from the bottom front of the machine.

1. there is a blockage in the filter or drain hose.takes too long to drain out.
2. over dosing of powder or liquid. again can cause an air lock in the pump which slows the drain pump down.

Check the filter and drain hose and test again. this fault will only come up at the end of a cycle.
You do not need to reset the machine to get rid of the fault code as this is automatically deleted.

Run an empty load with no detergent in an attempt to get rid of the code.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Feb 09, 2009 | Frigidaire GLTF2940E Front Load Washer

1 Answer

Mid wash I am gettign E10 messages


The manual suggests the following for E10 error --- 'The Water tap is not turned on.'
It is a valve fault.It is not taking the water in possibly. It is the green side of the triple valve. Try manual clearing the valve.Else The water inlet valve might need a replacement.
Good luck with the machine.Please do rate my solution.Also do post comments for further help if needed.

Jan 24, 2009 | Zanussi WJS1265W Front Load Washer/Dryer

3 Answers

E60 error code


Found These Fault Codes On Internet, Hope This Helps, Daz

ALARM CODES

E00(E00)- Problems with water fill during washing
-Tap closed; solenoid valve, water distributor, wiring ,main PCB, pressure switches

E01(E00)- Problems with water fill during drying
-Tap closed; solenoid valve, wiring , main PCB, pressure switches

E10(E10)- Problems with water drain during washing
-Drain hose kinked, filter blocked, drain pump, water distributor, wiring , main PCB, pressure switches

E11(E10)- Problems with water drain during drying
-Drain hose kinked, filter blocked, drain pump, pressure switches

E20(E20)- Door open
-Cycle in Door delay, wiring , main PCB

E21(E20)- Fault in door delay power triac
-Wiring , main PCB

E30- Fault in electronic pressure switch
-Electronic pressure switch, wiring , main PCB

E31- Fault in electronic pressure switch circuit
-Main PCB (fault in electronic pressure switch circuit)

E32(E10)-Calibration error in electronic pressure switch
-Electronic pressure switch, drain pump, wiring , main PCB, filter blocked

E33- Incongruency between electronic pressure switches and safety switch 1
-Electronic pressure switch, safety pressure switch,wiring, main PCB

E34- Incongruency between electronic pressureswitches and safety switch 2
-Electronic pressure switch, safety pressure switch,wiring, main PCB

E35- Intervention of anti-overflow pressure switch
-Solenoid valve, water distributor, wiring, main PCB,anti-overflow pressure switch

E36- Water leakage (maximum number of resets exceeded)
-Water leakage, drain hose too low, pressure switch,wiring, main PCB

E40- Motor power triac short-circuited
-Main PCB (triac short-circuited)

E41- No signal from tachimetric generator
-Tachimetric generator on motor, wiring, main PCB

E42- Fault in tachimetric generator circuit
-Main PCB (tachimetric generator sensing circuit)

E43- Intervention of motor overload protection
-Motor, wiring, main PCB

E50- Insufficient heating during wash phase
-NTC sensor setting incorrect, heating element, wiring,main PCB

E51- Overheating during wash phase
-Heating element (to earth), main PCB (relays)

E52- Insufficient heating during drying phase
-NTC sensor setting incorrect, safety thermostat,thermostats, drying heater, wiring, main PCB (relays)

E53- Overheating during drying phase
-Drying heater (to earth), main PCB (relays)

E55- Fault in power relay for heating element (K3)
-Safety pressure switch 2, wiring, main PCB- 6 -

E60- Fault in washing NTC sensor
-Washing NTC sensor, wiring, main PCB

E61- Fault in drying NTC sensor(condenser)
-Drying NTC sensor (condenser), wiring, main PCB

E62- Fault in drying NTC sensor(duct)
-Drying NTC sensor (duct), wiring, main PCB

E63- Fault in 1/2 power thermostat
-Drying NTC sensor (duct), 1/2 power thermostat, wiring,main PCB

E70- Power triac to distributor motor short-circuited
-Main PCB (triac short-circuited)

E71- Fault in power relay to distributor loads
-Main PCB (relay open)

E72- No distributor position signal
-Water distributor motor, wiring, main PCB

E73- Incorrect timing on distributor contacts
-Water distributor, wiring, main PCB

E90- Fault in tank fill pump
-Hoses obstructed, tank fill pump, wiring

E91- Fault in tank drain pump
-Hoses obstructed, tank drain pump, wiring

E92- Fault in power triac to tank fill pump
-Tank fill pump, wiring, main PCB

Jan 04, 2008 | Zanussi ZWF1440 Front Load Washer

Not finding what you are looking for?
Zanussi FJD1466W Front Load Washer Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

shaun taylor

Level 3 Expert

1527 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...