Question about Code-Alarm Code Alarm Transponder

1 Answer

OEM Ford remote starter quit working.

OEM remote starter installed on my wifes 06 Escape by local "experts" quit working. The dash gages go thru the little dance but starter fails to engage. I didn't get an operators manual for it, so I have no idea on how to reset or program.

Any ideas?

Dave in Erie, Pa

Posted by on

  • KheSanh1968 Apr 05, 2009

    Holding fob and pushing Key image button I'll get one beep after 10 seconds and no starting motor. The vehicle can not be started with the key until I hold the same remote for another beep. '07 Ford 500 Limited. No directions. Dave

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Interface kit went lifetime part

Posted on Jan 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a Spy brand one-way car alarm/remote start for my wife's 09 Camry. Everything is installed, and works except for the remote start.


Installations of this nature are usually reserved for professionals. However, get out your installation manual. You will also need two single pulse double throw relays and some diodes. First you will need to locate the ground when running.This wire might be labeled " (-) third ignition". The first relay for the starter will be wired like so: starter wire to 86, fused 12 volts to 87, 30 out to vehicle second starter wire, 85 to ground when running. The second relay will be wired 86 to vehicle ignition, 87 to fused 12 volt, 30 out to second ignition, and 85 to ground when running.

Jan 22, 2013 | Brand Remote Start/keyless/car Alarm Very...

1 Answer

My car quite starting from viper remote :(


Does it power up (meaning do you see the dash light come on)? Does it turn the starter?

Dec 18, 2012 | Remote Start System

2 Answers

Last Year I installed an AVITAL5103 Remote start & Security on My 2002 DODGE RAM 1500 Q.Cab.Everything was working fine,util I instal a new car battery.When I attempt to remote stert ,the starter cra


There are two types of starters for Dodge, if you installed new battery, check to see if the remote start is to ignition module or starter solenoid, then make sure the circuit has not been closed-they go in series circuit!

Nov 29, 2011 | 5103L Security/Remote Start System

1 Answer

My truck wont start when i use the remote. the power in the tuck turn on but the truck never turns over. 2006 ford f-150


Sounds as if your immobilizer bypass is malfunctioning. To test, remote start vehicle. Check vehicle cluster (gages). If the immobilizer bypass is the issue, there will be car/lock symbol flashing rapidly. To confirm, put the key in the ignition(do not turn), remote start the vehicle. It should start. If the vehicle starts, remove key, remote start again without key. If the vehicle does not start, have the immobilizer serviced. If the vehicle does not remote start with the key in the ignition, the issue may be with the remote starter's starter output.

Jul 25, 2011 | Prestige Remote Start

1 Answer

Try to start my 06 rx8 with car starter and only my dash lights go on then shut of 3 times without my car turning over. The key port is also locked.


It sounds like the bypass module is not bypassing. The next time that you attempt to remote start the vehicle, look at the cluster for a flashing key. If there is a key inside a car flashing...your bypass module is not functioning.

Nov 29, 2010 | Remote Start System

1 Answer

I have a 2004 tacoma. Remote starter doesn't work. Dash lights on right side of the dash are dim. Remote starter was pro installed 4 years ago. Any ideas? Thanks


look under dash for the unit, remove the 2 fuses in red jackets wait 2 minute then replace fuses

if you have a 4 BUTTON REMOTE CONTROL:
You will need to take the unit out of safety mode, to do this you will
need to ground the hood pin switch wire, then put your foot on the brake,
next hit any button on the remote and the clicking will stop. Then you will
need to take the hood pin switch wire off of ground and take your foot off
of the brake and see if the remote will work with the unit

if you have a 2 BUTTON REMOTE CONTROL:
You will need to take the unit out of safety mode, to do this you will
need to put your foot on the brake, next hit any button on the remote and
the clicking will stop. Then you will need to take your foot off of the
brake and see if the remote will work with the unit

Dec 15, 2009 | Bulldog Remote Starter & T-Harness Kit for...

2 Answers

Installing remote starter


depent of the car go to bulldogsecuryty.com

Mar 15, 2009 | JBS Add-on remote starter

1 Answer

Remote starter stopped working


Will you rate my answer from my clarification as a solution about the antenna thanks Mike humble.

Dec 11, 2008 | Vehicle Parts & Accessories

1 Answer

Prestige aps-57 remote start...car won't start


Hello hope this can help you. First check the starter wire, it is tan/lt blue located at the ignition harness. usualy during installation of the remote start system this wire is cut leaving you with two ends. one wire is coming from the ignition switch the other is going to the starter. the brain of the alarm hooks into both of these wires. if the repair man cut the wires from the brain and spliced them together he has just put the system back to OEM status leaving the alarm no way to engage the starter. I believe that may be where the problem lies but if not then I would say check your immobilizer bypass module the repair man mave have diconected that.

Thank you,
Luis

Dec 01, 2008 | Prestige Remote Start

Not finding what you are looking for?
Code-Alarm Code Alarm  Transponder Logo

Related Topics:

884 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Vehicle Parts & Accessories Experts

xxxxxx xxx

Level 3 Expert

4748 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13228 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Ford Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...