Question about Miele Air Purifiers

Open Question

Power Switch is stuck..

Appears that power switch is pressed in. Fortunately it is in the on position and will not turn off. How do I replace the switch? Suggestion on where to get Miele parts?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lasko Tower Fan stopped working but Speed switch has power on all but one cable, How to find the issue?


you should only have power on the black wire into the switch. The white wire feeds straight through. the switch breaks the black and routes it to one of the three outputs for the motor.

Aug 07, 2014 | Lasko 2510 36" Tower Fan with Remote...

1 Answer

My XL-15 won't power up. Everything seems to be in place but when I flip the power switch to the on position, nothing happens. I have looked at the fuse and it looks ok. Could there be another...


Hi Jan,

If the fuse is good and you are sure your outlet has power, then check the safety switch is being depressed. On the back is the lint screen, there should be a clip that depresses the switch. Hope this helps you.

Jun 30, 2011 | Alpine Air XL-15 Air Purifier

1 Answer

How do you turn off the little red filter llight above the low speed indicator?


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Nov 28, 2010 | Filter Queen Defender Air Purifier

1 Answer

I have a constantly blinking red light above the lower setting arrow...how do i resolve the problem???


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Nov 19, 2010 | Filter Queen Defender Air Purifier

2 Answers

Replace air filter warning light to reset?


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.

If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Sep 30, 2010 | Filter Queen Defender Air Purifier

1 Answer

Blinking red light above the lowest setting on filter queen defender air purifier.


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.

If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Sep 23, 2010 | Filter Queen Defender Air Purifier

1 Answer

How do you reset the red light on the defender when you put in a new filter? My light has never went out and I think it is supose to .


It won't go out by itself.
1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.

If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Sep 16, 2010 | Filter Queen Defender Air Purifier

2 Answers

Sharper image ionic breeze air cleaner


I was able to find the power-on switch to be defective. The switch is a momentary normally off switch constructed of two contacts on a printed circuit board1.gif. After five years, the surface of the switch contacts became oxidized and no longer made electrical continuity when depressed. I rewired the two wires to a new momentary switch and both my Ionic Air Cleaners are working again.

Feb 18, 2008 | Sharper Image Ionic Breeze 3.0 Air...

3 Answers

Red Light on front of Filter Queen Defender


When the red light is blinking, press and hold both up and down arrows until the red light blinks RAPIDLY, release both for a second or two, and press and hold both again until it stops blinking. It cured my problem.

Mar 06, 2007 | Filter Queen Defender Air Purifier

Not finding what you are looking for?
Air Purifiers Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miele Air Purifiers Experts

kakima

Level 3 Expert

102366 Answers

yadayada
yadayada

Level 3 Expert

75814 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Miele Air Purifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...