Mitel sx-50 a 13 0008 station ring ground fault 0

Love your song 'Boys of Summer', and heard it on boom FM today!

How many people phone 911 where you are!

Mitel Superconsole 1000 User Guide - Business ...

https://bcstel.com > doc > Mitel-2ICP-SC1000-UG
PDF
When the console is locked out, it cannot be used to place outgoing trunk calls or to access console functions, except 911 Call alarms. You can still use the ...
94 pages

Viewing 911 Call Alarms - Mitel SUPERCONSOLE 1000 SX ...

https://www.manualslib.com > ... > User manual
Mitel SUPERCONSOLE 1000 SX-200 Manual Online: Viewing 911 Call Alarms. ... When a 911 Call alarm is raised, the console rings and the display shows.

Hi,my mitel superconsole 1000 is not working,on display is

https://www.fixya.com > Forum > Lands Phones > Mitel
Apr 25, 2017 - Hi,my mitel superconsole 1000 is not working,on display is show blinking ALARM above F5 and ... To read a 911 Emergency Call alarm message:

• 
  

  20 Most Recent Mitel Superconsole 1000 Questions & Answers

  https://www.fixya.com > ... > Mitel
  Press Function 2.Press [ALARM] 3.Press [SHOW 911] This will show what extension calls the 911. 4.Record the number of the extension from which the 911 call ...
  
  ..

https://www.manualslib.com/manual/525349/Mitel-Superconsole-1000-Sx-200.html?page=74




http://edocs.mitel.com/UG/EN/9189-953-001-NA_2.pdf


Page 63

https://community.spiceworks.com/topic/2118453-mitel-phone-system-sx-200-superconsole-1000-no-wake-up-call-function



Mitel SUPERCONSOLE 1000 SX 200 User Manual Setting canceling Wake up Calls

defective , replace or exchange

first make sure it is not a line problem by disconnecting the phone line when you get the rings, then make sure it is getting proper power to the unit. if it does not have electric plug look for batt in unit and replace. If unit is dirty, gummed up try blowing out with air, before giving up on the unit. good luck

If they are digital phones then it could be a bad card

This is explained in the SX-50 system maintainer's handbook, 2 copies of which came with your SX-50 when it was new. However, this is a pretty old piece of phone equipment (30+ yrs) and when these systems were originally set up by outside service companies, it was not unusual for them to take the manuals so that customers would not be tempted to tamper and would call the service co instead. However, all is not lost. There is a very good Mitel support group on Tek-Tips (www.tek-tips.com) On tek-tips the Mitel forum is under Home->Forums->Wiring Closet->Phone Systems->Mitel Networks Solutions Forum. You will need to register in order to post. Hope this helps.

I have same problem on my sx-50 mitel consol, can any one solve this problem?

From a DTMF station set installed as the test line on equipment #1, go into trunk group programming (Command #66)
The SX-20 display will show programming registers.
A B C D E F G H
A,B = Trunk equipment Number (1st trunk should be displayed)
C = Register 1
D = Trunk Group Membership 0 = Incoming only
1 = Group 1
2 = Group 2
3 = Group 4
4 = Group 4
E = Trunk Type 0 = Standard CO Trunk
1 = Dictation Trunk
F = Reversal Meaning 0 = Not Incoming of Disconnect
1 = Incoming Call
2 = Incoming Call or Disconnect
G = Disconnect Timing 0 = 60ms
1 = 500ms
2 = 1.5 sec
3 = 4 sec
H = Start Type 0 = Loop Start
1 = Ground Start
Move to the appropriate register using the ENTER/NEXT function (star key).
Change the data as required.
Exit programming (# key)

Hope this helps!

You can switch to "night" mode on the console and the incoming calls should ring on the cordless. try it.

Hi,

If you have the SX -200 series 410 then here is your manual.

http://edocs.mitel.com/UG/EN/SX-200_SS410_ug_en.pdf

If you have the SX -2000 series 410 then here is your manual.

http://edocs.mitel.com/UG/EN/2k_410.pdf

It looks like from reading them though, that your IT department (PBX Administrator) will be the people you will need to contact to reset your code. Or if that does not work for you then I would contact Mitels customer support and see if they can walk you through it.

http://www.mitel.com/DocController?documentId=10095

Hope it helps, and let me know if you need more help or information.

Thanks!