Question about Toshiba 57H81 57" Rear Projection Television

3 Answers

Toshiba 57H81 Flashing Red Power Light, Blown Fused F850+F852

Toshiba Model 57H81 Rear Projection TV - Purchased 11-09-2001

Problem: Toshiba 57H81 Flashing Red Power Light, No Picture/Sound, Blown Fuses F850 + F852

Symptoms January, 2009:

  • Upon turning on set I got flashing red power light and nothing else.
  • Removing plug for one minute and plugging in results in:
    • Audible click, steady red power light for 2 seconds then slow flashing red light
    • Pushing power button results in steady red for about 2 seconds then slow flashing red light, no other set activity
  • Removing power cord for several hours and plugging back in made no change
    • Audible click, steady red for about 2 seconds then slow flashing red light
  • Possible related note: Over past several months occasionally the entire screen would flicker momentarily and at other times be problem free for weeks.
  • Fuses F850 and F852 found blown

Repairs Made:
  • PD0074 DEF/CON Power Board
    • There are two main power supply capacitors in this set. They are C-809 and C-810. One their negative lead on the printed circuit board re-soldered leads and nearby contacts. I’m told that because the factory left out a printed circuit board eyelet, the connection will come loose over time. When I called Toshiba customer service they said there was a known solder joint problem causing blinking red light.
    • Replaced blown fuses F850 and F852.
      • I actually installed a fuse panel on the inside of the cabinet and routed the fuse connections here instead of ordering the special fuses and replacing them on the circuit board.
      • Had to use a 5 Amp SLO-BLOW for F850. Fast blow does not survive power up. Get the red blinking light.
      • Used a fast blow 2 Amp for F852.
  • PD0073 SIGNAL Board
    • Re-soldered Q751 + Q752 STK392-110 Convergence Amps
    • Re-soldered adjacent pads that looks suspicious

Total Cost to Repair about $10
  • Twelve hours of my time over three days to research issue, disassemble set, make repairs, add fuse panel.
  • Already owned Service Manual and Circuit diagrams from a different 2004 repair.
  • Less than ten dollars at Radio Shack for fuses and fuse panel. Already had wires, etc.
  • Some solder. Already owned de-soldering tools, etc.
  • Visited both local authorized Toshiba factory service repair facilities. One said repair would have to include replacing Q751 + Q752 STK392-110 Convergence Amps with ST392-180, and realigning set for a total of $500+ and it would be more if they had to order a power board. NO THANK YOU! Other shop said $65 for site visit and $30 to make an estimate that could be applied to repair.

Posted by on

  • Anonymous Jan 27, 2009

    I have the same problem with a 50HX81. What component caused the fuses to Blow? I have yet to check the cap's (only visual) but replaced the convergence IC's. Did you put in the fuse panel for ease of access? If so can you tell me the specifics? thanks.

  • Anonymous Mar 01, 2009

    Thanks for the original post. What is the recommended wire size for the fuses? Thanks.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Estou com uma tv toshiba md 57h81que estar com dente de serra sobre a imagem deslocando-a da direita para a esquerda e um traco vertical tipo descarga de raio no lado direito da tela parecendo falta de sincronismo v. h. ou faze horizontal

Posted on Aug 11, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I had same problem. I checked picture tube by disconnecting them 1 at a time. Start with blue which is most common. Unplug tv and disconnect the tube from the board.Now plug tv in. If it comes on you have the right tube. If it doesnt try the others one at a time.

Posted on Feb 11, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Solved by resoldering some solder joints!!!!!!!
********
Toshiba Model 57H81 Rear Projection TV - Purchased 11-09-2001

Problem: Toshiba 57H81 Flashing Red Power Light, No Picture/Sound, Blown Fuses F850 + F852

Symptoms January, 2009:

  • Upon turning on set I got flashing red power light and nothing else.
  • Removing plug for one minute and plugging in results in:
    • Audible click, steady red power light for 2 seconds then slow flashing red light
    • Pushing power button results in steady red for about 2 seconds then slow flashing red light, no other set activity
  • Removing power cord for several hours and plugging back in made no change
    • Audible click, steady red for about 2 seconds then slow flashing red light
  • Possible related note: Over past several months occasionally the entire screen would flicker momentarily and at other times be problem free for weeks.
  • Fuses F850 and F852 found blown

Repairs Made:
  • PD0074 DEF/CON Power Board
    • There are two main power supply capacitors in this set. They are C-809 and C-810. One their negative lead on the printed circuit board re-soldered leads and nearby contacts. I’m told that because the factory left out a printed circuit board eyelet, the connection will come loose over time. When I called Toshiba customer service they said there was a known solder joint problem causing blinking red light.
    • Replaced blown fuses F850 and F852.
      • I actually installed a fuse panel on the inside of the cabinet and routed the fuse connections here instead of ordering the special fuses and replacing them on the circuit board.
      • Had to use a 5 Amp SLO-BLOW for F850. Fast blow does not survive power up. Get the red blinking light.
      • Used a fast blow 2 Amp for F852.
  • PD0073 SIGNAL Board
    • Re-soldered Q751 + Q752 STK392-110 Convergence Amps
    • Re-soldered adjacent pads that looks suspicious

Total Cost to Repair about $10
  • Twelve hours of my time over three days to research issue, disassemble set, make repairs, add fuse panel.
  • Already owned Service Manual and Circuit diagrams from a different 2004 repair.
  • Less than ten dollars at Radio Shack for fuses and fuse panel. Already had wires, etc.
  • Some solder. Already owned de-soldering tools, etc.
  • Visited both local authorized Toshiba factory service repair facilities. One said repair would have to include replacing Q751 + Q752 STK392-110 Convergence Amps with ST392-180, and realigning set for a total of $500+ and it would be more if they had to order a power board. NO THANK YOU! Other shop said $65 for site visit and $30 to make an estimate that could be applied to repair.

Posted on Jan 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

TOSHIBA MODEL 32RV530U WILL NOT TURN ON YELLOW LIGHT IN FRONT BLINKS 3 TIMES


This could very well be a problem with the power supply not allowing the TVs to start up but can also be caused by a problem with the TVs firmware. I would suggest downloading the firmware and following the steps from the following link. The download and steps are in the firmware tab after clicking the link. Be sure that even if you have no picture while applying the firmware update that you under no circumstances remove power from tv for at least 15mins. This is to ensure the firmware completely loads. If you remove power while it's still updating the board may be corrupted. http://support.toshiba.ca/support/ceg/center/en/index.asp?p=32RV530U

Jan 13, 2017 | Toshiba REGZA 32RV530U LCD TV

1 Answer

My toshiba tv keeps fading to black


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electro-medical.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board....

Jan 10, 2017 | Toshiba Televison & Video

1 Answer

I have a Philips flat screen TV, Model 50PF9630A/37 i replaced some blown cap on the power supply board now the red light flashes in a sequence of 7 flashes, any assistance would be appreciated.Guy


Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/

Jan 10, 2017 | Philips Televison & Video

1 Answer

There is a light flashing coming from behind the back of my tv it's a flat screen


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis. http://electronicshelponline.blogspot.com/ To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Jan 09, 2017 | Televison & Video

1 Answer

Why won't my LC-32CHF5111K tv turn on I have a steady glowing red stand by light


It could be the power supply board on the TV. It could also be a blown capacitor on one of the circuit boards.

Jan 08, 2017 | Televison & Video

2 Answers

Where do I find the serial number on vizio tv model D48-d0


Below the model number on back of tv right rear corner

Jan 08, 2017 | Vizio Televison & Video

1 Answer

Tv will not turn on, orange light flashing


Could be an open internal fuse or power supply failure

Jan 07, 2017 | Televison & Video

1 Answer

Replaced convergence on toshiba 42HDX82...put back together now no picture or sound...could i have rehooked up wires wrong?


YES YOU COULLD HAVE WRONGLY HOOKED UP THE WIRES AND TANGLED THEM UP WHICH IS CAUSING THIS TO HAPPEN BECAUSE ITS CAUSING THE THE VOLTAGE THE TO ENTER AND CAUSING THIS TO HAPPEN

Nov 30, 2016 | Toshiba 42HDX82 42" Rear Projection...

1 Answer

I recently got a 51h83 toshiba tv. When i try to hook up my xbox 360 with the hd component cables in the back i get sound but no video. Please help.


WITH THE TOSHIBA 51H83TOSHIBA TV YOU CANT HOOK UP HD CABLES TO THAT SPECIFIC TV FROM YOUR XBOX 360 BECAUSE THE DEVICE ISNT EQUIPPED WITH THAT CAPABILITY

Nov 16, 2016 | Toshiba 51H83 51" Rear Projection...

Not finding what you are looking for?
Toshiba 57H81 57" Rear Projection Television Logo

1,793 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71672 Answers

Jaime Hernandez

Level 3 Expert

2294 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...