Question about Washing Machines

1 Answer

Maytag Bravos Quiet 300 Auto. washing machine won't wash, DL code appears. Also, the 'add a garmet' light won't turn off. How can I fix the problem?

The DL code appears when I try to wash clothes. The "add a garmet" light stays on constantly and I can't get it to turn off. Any help will be appreciated.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Washing Mach... Master
  • 9,472 Answers

What is the model number?

Posted on Oct 31, 2012

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

kel1guy2002
  • 3740 Answers

SOURCE: My Maytag Bravos quiet series

Hi and welcome to FixYa, I am Kelly.
My response is very long and will be in 2 parts this is PART 1

Here is what the service manual says about Ld:

"Ld" (Washer is taking too long to drain

water from the wash tub)

Check the following:

Is the drain hose kinked or clogged?

Is the drain hose installed properly? See

"Connect the Drain Hose," page 2-5. Press
PAUSE/CANCEL to clear display
Also:

Is the drain hose clogged, or the end of

the drain hose more than 96? (244 cm)

above the floor?
See "Drain System," page 2-3.
6. To remove the drain pump: (there are 2 pumps... the drain pump is on the left)

a) Loosen the clamps and pull the inlet

and outlet drain hoses off the pump.

Note that there is a tab on the outlet

connector that fits into a slot in the

hose.

b) Remove the three 5/16? hex-head

screws from the drain pump and remove
the pump from the tub.
Check the pump inlet and the tub outlet for obstructions.
Pump electrical winding resistance test:

-Disconnect the wire connector from the

drain pump terminals.

- Set the ohmmeter to the R x 1 scale.

- Touch the ohmmeter test leads to each

of the drain pump terminals. The meter
should indicate between 10.5 and 14 ?.

----Due to the design of the machine the 2 wires going to the drain pump have be notorous for backing out of the plastic connector. Check the connector of the pump for loose terminal connections. --

From the Ld troubleshooting steps / procedure:

Long Drain

Ld flashes when the water level does not change after the drain pump is on.

• Is the drain hose or the drain pump clogged?

• Is the drain hose height greater than 96? ?

• Is the pressure hose connection from the tub to the machine/motor control pinched or plugged?
• Is the pump running? If not, see TEST #7.

TEST 7

TEST #7 Drain/Recirculation

Perform the following checks if washer fails to drain or recirculate.

1. See Activation of Manual Diagnostic Test

Mode, and perform the Manual: Pumps

test.

2. Remove the console to access the machine/

motor control assembly. See Accessing

& Removing the Electronic Assemblies.

3. Visually check that the P4 connector is

inserted all the way into the machine/motor

control.

If visual check passes, go to step 4.

If visual check fails, reconnect P4 and

repeat step 1.

4. Remove connector P4 from the machine/ motor control and check resistance values of pump motor windings. Resistance values should match those shown in wiring diagram, page 7-1.

If resistance values are good, go to step 7.

If winding measurements are much higher (tens of ohms to infinity) than shown in wiring diagram, a problem

exists in the motor winding or in the connection between the machine/motor

control and the motor. Go to step 5.

5. Tilt machine forward to access the bottom

of the machine and the pumps. See
Figure 1, page 6-13.
6. Check the resistance at the pump motor. Remove the connector at the motor and

take measurements across pump terminals. Measurements should be as shown in the wiring diagram.

If winding measurements are much higher (tens of ohms to infinity) than shown in wiring diagram, replace the

pump motor.

If the resistance at the pump motor is correct, there is an open circuit in the wiring between the motor and the machine/

motor control. Repair or replace the lower wiring harness.

If the pump motor windings and machine/ motor control check OK, repair or replace the pump. Be sure to check

the pump and tub sump for foreign objects before replacing pump.

7. See Activation of Manual Diagnostic Test Mode, and perform the Manual: Pumps test.

8. If the Manual: Pumps test failed, then the machine/motor control has failed:

Unplug the washer or disconnect power.Replace the machine/motor control assembly.
Perform the Manual: Pump test.

Posted on Nov 21, 2010

SOURCE: Get a "F51" code on

Go to http://www.servicematters.com/docs/wiring/Tech%20Sheet%20-%208567036.pdf

It shows what the codes mean. It's been fixed by people (when machines are out of warranty!) by taking the control panel, and reseating wires on it and the motor.

You are by no means the only having the problem:
http://worldofwashers.blogspot.com/search/label/f51

Posted on May 01, 2008

  • 1 Answer

SOURCE: my maytag bravos quiet series 300 washing machine

i lost the manual , what does "5d" mean when it is

Posted on Jul 04, 2011

TheMobilian
  • 8220 Answers

SOURCE: MAytag Bravos Quiet Series 300 washing machine

F-51 RPS senses rotation when basket ought to be stopped.
It is probably loose or worn out.

Video How To

Posted on Oct 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the HC code mean on the Maytag Bravos Quiet Series 300 mean?


You can fix it. Your hot and cold water hoses are reversed on the water valve on the washer. Switch them around you should be fine.

Sep 08, 2014 | Washing Machines

2 Answers

Maytag Brovo 300 seies washer display says dl and will not wash


The error code "dl" is for door lock. From what I've read, it may mean you need to replace the latch assembly.

Sep 07, 2014 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

My maytag bravos washer is flashing DL, what does this mean, its not spinning!


The "dL" error code appears when an item inside the washer prevents the lid from locking properly. Open the washer and readjust any items that may be hitting the lid. The error code should go away once you properly close the lid

May 03, 2012 | Maytag Bravos 3.8 Cu. Ft. Washer

2 Answers

MAytag Bravos Quiet Series 300 washing machine starts to fill, stops and shows code F51


F-51 RPS senses rotation when basket ought to be stopped.
It is probably loose or worn out.

Video How To

Oct 22, 2011 | Maytag Bravos 3.8 Cu. Ft. Washer

1 Answer

Maytag bravo quiet series 300: Stopped at spin:


We have a Maytag Bravo Quiet Series 300 washing machine, the door latch is broken. I have the replacement part ( the locking mechanism) but I need can not figure out how to get the top of the washer to flip up to give me access to top front of the machine to remove the old part and replace it with the new.

How do I flip back the top (not the door) of this machine?

John

Jan 15, 2010 | Maytag Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...