Question about Powermatic 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30" Accu Fence System

2 Answers

Need a rocker switch for a Powermatic 63 A Artisan table saw part number 6285322

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you want to buy a new one, the Grizzly G1022 Table saw is an exact replica of the PM#63. A owners manual and parts list is available at their website. Grizzly.com

Posted on Apr 12, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Fix the old switch by unpluging then remove the switch ( 2 screws) and take it apart, (3 screws and 2 tabs) polish the contacts by removing the 2 contact plates and smoth up with 300 sand paper for the 2 contacts left in the fousing I used a dremel with a stone with a flat end. Reassemble

Posted on Jan 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I repair the tilt on my artisan table saw ?


I'm not familiar with your saw, but I'm familiar with table saws in general.
The tilting is achieved by a worm screw on the end of the crank handle engaging a partial worm gear on the tilt mechanism.
If all you get is clicking, the worm is jumping out of the teeth on the worm gear. It's likely that the shaft you're turning has slid a bit in its bearing and the far end of the worm is no longer constrained and no longer holds the worm tightly against the worm gear.
I'd say just take the whole thing apart and re-assemble it. In the process, you'll find out how the worm has slipped out of place and you'll see how to put it back where it belongs so that the worm is supported on both ends.

Oct 15, 2014 | Powermatic 1791227K Model 64 10" Artisan...

1 Answer

How do you set tension on overlocker


I have no idea what an overlocker is. Help me out.

Aug 31, 2014 | Powermatic 1791227K Model 64 10" Artisan...

1 Answer

What belt(brand/numbers)to replace the one on a Powermatic Artisan 63A Table Saw?


Probably a long out of date question but my suggestion is to purchase a link style belt to replace the old hard drive belt that comes with the saw. It'll deliver more power to the blade, run quieter and work better. I also recommend replacing the drive pulleys while you're at it. Get a couple of balance ones.

You can get a link belt at Rockler or other woodworking outlets.
http://www.rockler.com/1-2-power-twist-plus-link-v-belt

Jun 19, 2014 | Powermatic Table Saws

1 Answer

Difficulty raising and lowering the blade on Delta rockwell10" unisaw 34-450


Ok, basic question...is the lock engaged? It is the small knob at the center of the adjustment wheel. Is it possible the screw has been galled?
Here is the manual- http://content.powermatic.com/manuals/1791227K_man.pdf

May 27, 2014 | Powermatic 1791227K Model 64 10" Artisan...

1 Answer

Table saw won't start


You can only tell by using a continuity tester or a multimeter and some troubleshooting techniques.

Nov 10, 2013 | Powermatic 1791227K Model 64 10" Artisan...

1 Answer

I am trying to find out how old my powermatic 66 table saw is. serial no is 97661400


On the Powermatic 66's the first two numbers are the year in which it was made, so yours was made in 1997. The second set of two numbers is the model. The last numbers I"m unsure of but its my understanding that they represent the manufactured number, so yours was the 1,400th saw made for that year.

May 27, 2010 | Powermatic 66 10" 3 HP 1 Phase 230V Table...

1 Answer

Aline table to blade


align blade and fence to mitre slot.

Jan 26, 2010 | Powermatic 1791227K Model 64 10" Artisan...

1 Answer

Vibration in powermatic model 66


No. Unplug saw remove saw blade grasp shaft that saw blade was on wiggle back and forth. Should not be too much play. After 10 years motor bearings are proably worn. Easy to replace

Aug 07, 2009 | Powermatic 1660802K Model 66 Special...

1 Answer

Where can I purchase a table saw insert for a powermatic 63 like the metal insert that was original when I bought the saw in 1989. thanks


I would try calling powermatic here. They'll be able to get the part number and let you know whether they have it available, or if it's compatible with currently produced models.
Unless you have the part number from the manual, their web site is hopeless....

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Jul 03, 2009 | Table Saws

Not finding what you are looking for?
Powermatic 1791227K Model 64 10" Artisan Left Tilt Table Saw with 30" Accu Fence System Logo

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Powermatic Table Saws Experts

80stech

Level 2 Expert

92 Answers

Dennis Key
Dennis Key

Level 3 Expert

2444 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Powermatic Table Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...