Question about HP Computers & Internet

2 Answers

A 1xx POST error code indicates a problem with the ??

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • HP Master
  • 2,072 Answers

That would be the motherboard. Here are the 100 codes

1xx

System board

101System board; Interrupt failure102System board; Timer failure103System board; Timer interrupt failure104System board; protected mode failure105System board; last 8042 command not accepted106System board; Converting logic test107System board; Hot non-maskable interrupt test108System board; Timer bus test109System board; Memory select error110PS/2 system board; Parity check error111PS/2 memory adapter112PS/2 MicroChannel arbitration113PS/2 MicroChannel arbitration114PS/2 External ROM checksum error115Cache parity error, ROM checksum, or DMA error116System board port read/write failure118System board parity or L2-cache error during previous power-on119"E" Step level 82077 (floppy controller) and 2.88M drive installed (not supported)120Microprocessor self test error121256K ROM checksum error (second 128Kb bank)121Unexpected hardware interrupts131PC system board cassette port wrap test failed131DMA compatibility registers error132DMA extended registers error133DMA verify logic error134DMA arbitration logic error151Battery or CMOS RAM failure152Real-time clock or CMOS RAM failure160PS/2 system board ID not recognized161System options not set; dead battery162System options not set; CMOS checksum/configuration error163Time and Date not set; clock not updating164Memory Size error; CMOS setting does not match RAM165PS/2 system options not set166PS/2 MicroChannel adapter time-out error167PS/2 system clock not updating168CMOS configuration error (math co-processor)169System board and processor card configuration mismatch170ASCII setup conflict error170PC Convertible; LCD not in use when suspended171Rolling-bit-test failure on CMOS shutdown address byte171PC Convertible; base 128K checksum failure172Rolling-bit-test failure on NVRAM diagnostic byte172PC Convertible; diskette active when suspended173Bad CMOS/NVRAM checksum173PC Convertible; real-time clock RAM verification error174Bad configuration174PC Convertible;LCD configuration change175Bad EEPROM CRC #1175PC Convertible;LCD alternate mode failed176Tamper evident177Bad priviledged-access-password CRC177Bad EEPROM178Bad EEPROM179NVRAM error log full181Unsupported configuration182Priviledged-access switch (jmp 2) is not in the write-enable position183PAP is needed to boot from the system programs183PAP is required184Bad power on password checksum - erase it184Bad power on password185Bad startup sequence186Password-protection hardware error187Serial number error188Bad EEPROM checksum CRC #2189Excessive incorrect password attempts19182385 cache controller failure194System board memory error199INSTALLED DEVICES list

Posted on Nov 18, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • HP Master
  • 102,366 Answers

It indicates a problem with the system boards. For more info, start here.

Posted on Oct 30, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F13 code


Hello friend, thank you for your post!

Based off the information you have provided your question is under an "F13" error code but you also stated that it is showing you an "F1" error. I have researched both error codes for you. "F13" usually indicates error identification, which could be an issue within your control board. "F1" typically can indicate that the range has detected an issue with the runaway temperature (overheating). Both codes could be corrected with a reset, which you can do by flipping the household circuit breaker for roughly ten minutes. If that does not correct the issue I would recommend contacting a professional. I hope this is helpful. -Matt

Aug 07, 2014 | Frigidaire Ovens

Tip

Beep codes


Diagnostics with Beep Codes Following are the beep messages associated with the IBPbios. 1 short beep specifies a normal post 2 short beeps tells about POST errors that can be find onscreen. Continuous beeps indicates power supply and other cardserrors. One long and short beep indicates system board problems 3 long beeps defines keyboard errors No system beep tells about power supply errors.

on Mar 15, 2011 | Computers & Internet

1 Answer

E00 code what does this mean


Hi William, thank you for your post!

If you are getting error code E00, it usually indicates that your washer is experiencing a generic error. One of the best ways to determine if this is a false error code is to reset the power to the appliance by either unplugging it or flipping off the breaker for about 30 seconds. If the error code

Nov 29, 2013 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

C-0102


The 1xx code refer to main body papre tray lift motor error.Check the paper jam in rear side to open the trays.To reset press the Utility key and hold on and turn ON the copier,wait will appaire Trouble reest on the display,release the Utility key,touch the screen and turn OFF the machine.Wait 2 minutes and turn ON.

Mar 05, 2013 | Konica Minolta bizhub Office Equipment &...

1 Answer

Windows fails to start on my e-machine w3623 with windows vista


where does the comnputer fail to load at. If you have installed windows again and the computer fails to start it is a hard drive or cable problem. Does the computer give you a error message (like 1XX,2XX,3XX Etc.

Sep 27, 2010 | eMachines W3623 PC Desktop

1 Answer

What does UE mean on a 4kg LG washer drier??


Hi!! UE Error Code is indicative of a "Unbalanced Error". This indicates that the drum is not spinning in a smooth rotation. It may be necessary to rearrange the load in the drum.
Don't forget to rate this post!!

Sep 15, 2010 | Washing Machines

1 Answer

Error 0210: Stuck Key 01


This is a system board POST/BIOS error code (nothing todo with Windows). The ERROR 210: is a standard POST (Power On Self Test) errormessage that indicates an error with the keyboard. The error condition is thata keyboard scan code was received from the keyboard when none was expected,after the keyboard was reset. If this occurs most of the time when you power on yoursystem, then it indicates that a key is sticking down or the key mechanical orelectrical parts are broken. Sometimes blowing out and cleaning out around thekeys will resolve this problem. Otherwise, you need to replace your keyboardwith a new (or at least a working) one.

Oct 17, 2009 | Lenovo ThinkPad R61i Laptop

2 Answers

Error code


You're right, it cross references to a "Ricoh FT4727". You need to press the "." key to read the last 2 digits, however "1xx" codes all relate to the optics section: For example, exposure lamp, scanner motor, lens, etc. You'll need a technician to fix this one.

Mar 28, 2009 | Ricoh Aficio 450 Copier

1 Answer

When i on the machine e-5 error appear and machie not working


What model? AND you need to press the "." key to get the complete code?
However... "E 5xx' " is a fuser code and will not go away until it is fixed and reset in service mode.

"E 1xx" is a scanner code, which means it is either a lamp, fuse , home position sensor...etc.

Mar 19, 2009 | Ricoh Office Equipment & Supplies

1 Answer

Diagnostic Indicator


Beep codes and power LED status are pre-post errors. Usually beep codes indicate a problem with a memory module. Power LED is solid green for normal operation. Solid or blinking Amber color power LED indicates a power distribution problem.




Your responses are intended to improve the level of service provided. Please show your appreciation by rating your experience.
Thank You.

Nov 13, 2008 | Dell Dimension 2400 PC Desktop

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

1,039 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18387 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Tony

Level 3 Expert

2600 Answers

Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...