Question about Mitsubishi Televison & Video

1 Answer

I have this Mitsubishi prjection 65 - 1080dp it does not want to turn on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 14,553 Answers

Look to see if ws, wt, vs model and if at turn on power light comes on for a few seconds and then goes out do the self check the set will have.

Posted on Oct 30, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 52": rca prjection tv turns on but just before


The deflection board has an issue and will need to be replaced. You can get the replacement deflection board from www.tvcircuitboards.com

Oct 21, 2011 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

TV WONT TURN ON


Encompass Parts Distribution has the Part number
for Lamp and Mats Electronics is where to buy Lamp 99.00 1-800-628-1118

May 05, 2010 | Panasonic PT-56LCX70 56" HDTV

1 Answer

My tv does not turn on at all i dont even get the green light on the front


older RCA prjection sets have HV block problems newersets have flyback an muliple problems

Sep 20, 2009 | RCA Televison & Video

1 Answer

Bright blue semi cirle on my prjection tv, lower


Hi

you have defective convergence correction circuit! this parts needs to replace a new one!

Thanks!

Jun 05, 2009 | Samsung HCM5525W 55" Rear Projection...

1 Answer

Tv wont turn on, RCA D56w20, 56" rear prjection


replace the flyback 259296 and the CP150 capacitor. You can get the replacement parts with free instructions at the following link.
http://servicemanuals.vstore.ca/

May 17, 2009 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Sony 57"kp-20fm12 hi scan 1080i rear prjection


That blinks and flashing have a diagnostic code. I have a list of the problems that might have occurred indicated by the number of blinks or flash. Tim just post the number of flash or blink,so i give you diagnostic code meaning...

Hope it may help you;

Regards,
VOTIT

Oct 02, 2008 | Sony KP-57WV600 57" Rear Projection...

1 Answer

Mitsubishi prjection screen WS-65908


You have a convergence problem,all this sets show this problem sooner or later,you have 2 or 3 amps for the red,green blue colors and this amps go bad and need to be replaced then you have to do a convergence aligment from the service mode and not form the customer controls,a qualified tech should be able to correct the problem since is a common one.

Sep 09, 2008 | Mitsubishi WS-65908 TV

1 Answer

Turnes off, sometimes in a short period, and sometimes it will go for hours.


this is a comon problem among rear prjection tvs, the lamp in the back is blowed or there might be power problems. whatever you do do not open the back. i shocked myself. technicians are costly because these tvs are outdated. i bought a new lcd.

Jan 15, 2008 | Mitsubishi WT-42311 42" Rear Projection...

1 Answer

Hitachi Projection TV power problems


Good Day,
If TV wont turn on check Q912, Q913 & I901. If no click of relay Check Q003, als chech the Convergence IC's.
Good Luck, big IRISH.

Jan 03, 2008 | Hitachi 50UX26B/27K 50" Rear Projection...

1 Answer

Mitsubishi 55-inch Prjection HD


If You cant adjust the convergence through the convergence menu. Chances are its your convergence ICs. Some mitsubishi set are famous for having bad solder joints on the ICs. I would check that out first, but be careful there is always a risk of getting shocked if your not famillar with TV diagnosis and repair, even after the plug has been pulled. If you feel comfortable checking the solder joints. you'll be looking for huge ICs attached to huge heat sinks with 18 pins. There are two seperate ICs

Oct 12, 2007 | Mitsubishi VS-55705 55" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1208 Answers

The Knight
The Knight

Level 3 Expert

73665 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...