Question about Juki TL-98Q

Open Question

Thread Cutter and needle problems

My machine is working just fine but when I stop sewing, my juki takes an additional 3 stitches before it stops. The 3 extra stitches are done in the slowest speed. I don't know how to make it stop when I stop. When I use my thread cutter, it speeds up the stitching but nothing is cut, it just goes up and down several times in the "normal" speed for cutting the thread. It wasn't always like this. The last time I took my Juki in it had got seized up on some fabric or thread, but when I got it back it started to do the two things above. I would love to be able to solve these problems on my own instead of taking it back in.

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
rylee_smith
  • 8619 Answers

SOURCE: juki 5555

You probably need to insert a new needle but here is a link that should help you Claven.These things happen to all of us at one time or another

Posted on Jan 30, 2009

Ad
  • 43 Answers

SOURCE: skip stitch

The three most obvious causes (other than that of the machine possibly being slightly out of time) are:

1) Too small of a needle size - increase the size.

2) A needle that has a flaw / defect - change the needle.

3) Needle not inserted correctly, either not pushed all the way up into the needle bar, or not installed facing the correct place. On this machine, the small "scarf" in the needle (an indent just above the eye) shouldface the right side of the machine.

Posted on May 07, 2009

SOURCE: we are hving problems with

hi there
1 - remove throat plat and mak sure the movment for thread cutter working or NO if working maybe need to change fixed knife or movable knife.
2 - if no movment mak sure plug for cutter solenoid is connect secur.
3 - make sure the output signal is coming to the cutter solenoid or no.
4 - maybe solenoid is dameged and need to change.
with my best regards
ashraf abozid
aabozid@hotmail.com

Posted on Dec 03, 2010

  • 1 Answer

SOURCE: Juki DDL-8700--top & bobbin thread won't hold together for stitch

What bobbins do I use on a Juki DDL-8300

Posted on Mar 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Needle thread is wrapping around the bobbin case on my juki ddl 5550N industrial. I've set the timing and it looks perfect to me...stitch looks good. Except when I stop and pull the work away from the...


Not to familiar with the industrial machines. However, even with domestic models. the position of the 'needle' bar at the time you remove your fabric, does make a difference as to weather it pulls our smoothly or, you are going to get that "extra" loop. Needle should be half way up or all the way. maybe this might help

Sewing Machine Tech

Oct 23, 2013 | Kenmore Drop-In Bobbin 16231 Mechanical...

1 Answer

I have a 2011 Juki DDL-8300N. Has always worked fine but while sewing on denim it suddenly seized up and stopped sewing. The needle is in the lowest postion through the jeans. I am unable to turn the


Your needle probably bent and got jammed. clip threads top and bottom of the fabric and remove... then get in the bobbin area and look for issues.

Sep 30, 2012 | Juki DDL-8300

2 Answers

My thread on the top of the material is stitched fine.. the bottom stitch ballons


try changing the needle
rethread the machine use every thread guide
check to see if the thread has come off the thread take up lever
clean under the needle plate & in the bobbin area for lint
if none of these suggestions work, then the machine needs to be
checked to see if there is a problem with the timing

Sep 23, 2012 | Juki Sewing Machines

1 Answer

My Juki MO-655 serger will sew a few inches then the needle thread becomes disengaged in the stitch process. The machine will sew a few inches more then stops making stitches. I have cleaned the thre


Make sure you are threading the machine correctly. Make sure you are using serger thread that isn't old. Make sure you are undoing all the threads when it breaks and thread it from the beginning.

Make sure you have the right needles in their respective places. My Juki MO has two different size needles.

Sep 02, 2012 | Juki MO-655 Mechanical Sewing Machine

1 Answer

Having problem sewing on leather. I have a juki 555-5 and it is skipping 1 stitch every 3 inches . I bought a roller foot kit and it did not work. I am so frustrated. If any one could help it would be...


make sure to use a leather needle
needle must be inserted correctly,,the falt side of the needle must face the shaft
the groove in the needle faces away from the shaft

raise the needle bar to the highest point,,then loosen the clamp screw to remove the old needle
push the needle all the way up to the stop, or as far as it will go,then tighten the needle clamp screw

also make sure the needle & thread will work togeather
Cut 6-8 inch piece of thread of the spool you are going to use for your project
Take the needle you are going to use for the project
& insert the thread thru the eye of the needle
& lift one end of the thread to a 45 degree angle
& if the needle is the right size for the thread it will slide down the thread
But if the needle hangs on the thread you need one size larger needle for the thread

also clean under the needle plate where the feed dogs are
also bobbin area

Nov 20, 2010 | Juki MO-644D Mechanical Sewing Machine

1 Answer

How do i stop juki ddl from top skipping stitches?


Hi. Skipped stitches are usually caused by a mismatch in your thread and needle. Wrong thread type, wrong needle size, or even old thread can cause skipped stitches. If all else fails, change the needle. If that doesn't work, clean the machine. Sometimes just getting rid of all the lint and giving her a good oiling does a world of good.

Let me know if this works.

Robbie

Jan 10, 2010 | Juki HZL-E80 Computerized Sewing Machine

1 Answer

My juki tl98q foot pedal and thread cutter has stopped working. help


Check the power cord and then take apart the side door and check the thread cutter for any displaced working machanisms. OK!!

Nov 28, 2009 | Juki TL-98Q

2 Answers

2nd needle/4th thread - threading confusion


With some sergers, but not many (singer 14u64 comes to mind), the top of the stitch will be an overedge that mates with the right needle thread, and the left needle thread will appear as a separate straight stitch. When you look at the underside of the stitch, the overedge will go all the way over to the left needle (the full width of the stitch). This is normal if you have this type of machine. Another stitch some sergers do (2/4 thread sergers) is a 2 thread chain thal looks like a lone straight stitch on both sides, and a 2 thread separate overedge.

As far as the threading of the takeup, it totally depends on your model. Always post your model number when you have questions as sergers vary greatly in design.

Mar 11, 2007 | Juki MO-644D Mechanical Sewing Machine

Not finding what you are looking for?
Juki TL-98Q Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Juki Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1125 Answers

Pete Alaniz

Level 1 Expert

13 Answers

SewTechWayne
SewTechWayne

Level 2 Expert

186 Answers

Are you a Juki Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...