I was printing a doc when my printer power lite started flashing and just stopped . now this printer will do this when it is out of ink or paper and display a message of the problem. but this time it just started flashing with no message. i have shut it off and restarted with no result. i have disconnected it , i have rebooted the computer. and so on and i can't figure it out. i am not sure if printer just died or if it is a usb problem the printer is about 3 or molre years old but the computer is just months old like maybe 3 to 4 months
An expert who has achieved level 2 by getting 100 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 500 times.
Re: printer stopped printing in the middle of a doc
Have checked the ink cartridge to see if it is empty? Sometime the the inki will run out and not display on the motitor. Have had this happen to one of my friends and that was the problem. Hope this helps. Bud
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
lets start with the basics.
Do a calibration of the label to the printer : -
1/ Turn off the power
2/Press and hold the feed key
3/ Turn on power and wait for the green feed light to flash twice.
4/ Release the feed key
5/ The printer should feed and print the configuration.
Now press the feed key and the label should feed and stop at the gap.
If this does not work , then let me know via this page.or contact me at the link below
What model is this printer? If it has a scanner/copier function, try copying something and see if it works that way. If it does, there is an issue with the computer. If it has a problem copying, it is a problem with the printer. Let me know and I can give you additional steps to take.
1. Turn off printer 2. Hold down Resume button and press Power button. 3. Keep holding down Power button and let Resume button go. 4. Press Resume button 2 times then let BOTH buttons go. 5. Green lights will flash and then stop blinking. 6. When green lights are solid, press the Resume button 4 times. 7. Press the Power button and the printer should turn off, if not, press the Power button once more. 8. Your printer should respond as normal
Sound like residue from the protective tape that was on the cartridge. Take the cartridge out and clean the copper contacts with a Q-Tip dipped in alcohol. VERY lite-ly... I have seen a lite glaze from the tape stopping proper contact if the were on the store shelf very long....
Please rate this solution if it helps.... Thank You...
ok you might have tried printing a doc/app out earlier and it might have failed so while you trying to print out this present app/doc the printer still might be focused on that failed or it might be confused. Now to stop this follow these instructions. Go to the start bar click control panel. Then once that window pops up ( control panel ) click printers and other hardware. Then once that window pops up ( printers and other hardware ). Click Printers and faxes and that page will have all the printers and faxes ever installed to your computer. Now click on the printer thats yours and then a smaller wider window will appear you will that window will have all the doc/app you have ever tried printing out. the status bar will show what is going on with each doc/app. Now you should first stop all the doc/apps and refresh. To do this you should highlight all the doc/app and then go into the document tab ( there are several tabs in this window such as document , printer, view and help) then click cancel and cancel all the doc/apps. last step is to go into the view tab and click refresh and it should work :-). If not contact your printer manufactor.
It appears that the injection may have been lethal, it was still using the ink that it carries in its tubes then it mixed with the injection and is now blocked \ faulty. To repair it you could try getting a new set of HP inks.
Power off printer and covers closed
Hold down the Resume button then press and hold POWER, the Green Indicator will
light. While holding down POWER , release RESUME
Double click (2 clicks) RESUME then release BOTH POWER and RESUME and wait
still the printer stops blinking.
When the indicator lights steady, press RESUME three(3) times. The indicator
should be ORANGE.
Press Power to set data
I got the solution from the Internet at the following link: http://www.fixyourownprinter.com/forums/inkjet/15620