Question about Jenn-Air JGW8130DD Gas Single Oven

1 Answer

F1 fault code on Jenn-Air jwg 8130

Same as above

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 679 Answers

Hi,
The F1 ErrorOn a number of ranges this can mean a number of things, the most common being a failed ERC(EOC, Clock assembly)or a faulty touchpad. Firstly if you are using a recent Maytag range it may pay to test the oven sensor as described above as this may cause an F1 error if faulty (may apply to some other ranges as well) this is not a common cause but is worth discounting. To check the ERC and touchpad 
Disconnect the power
Gain access to the back of the ERC
Disconnect the ribbon cable that connects the ERC to the touchpad
Check nothing will short when power is reconnected
reconnect the power and switch on
Watch for F1 and listen for the beep
If you get the F1 and the beep this means the fault is with the ERC and it will need replacing 
If after 30 mins you do not see the F1 error and hear the beep, replace the touchpad

or follow the link for more info:
http://www.appliancefactoryparts.com/applianceshvac/help-center/fault-codes/fault-codes-ranges.html#Admiral

thanks for your question.

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F1E1 error happened repeatedly, jenn air says cut




F1 - E1
EEPROM checksum error
1.
Disconnect power for at least 30 seconds.
2. Re-apply power and observe for
at least one minute.
3. If code re-appears, replace control board (also
called ERC or clock).

Note: Applies to all F1-E...
codes except F1-E3.

Read more: http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx#Jenn
Air Range / Stove / Oven Fault Codes#ixzz19GMNtS3r


http://www.appliancepartspros.com

Dec 24, 2010 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

What does f1.mean?


Most Common F1 Error Code for jenn Air is : Touch Pad or Control Board

Oct 06, 2010 | Jenn-Air Ovens

1 Answer

Fault code F1 on a Jenn Air WM2780. Upper oven


Usually this is a problem with the control board. The board can be repaired at www.fixyourboard.com.

May 21, 2010 | Jenn-Air JJW8230D Electric Double Oven

1 Answer

What does F1 mean on my oven


F1 code for Jenn Air is related to the main electronic control board. If you can turn your breaker off for a few minutes then back on it may reset. If not you will most likely need a new control board. Depending on your model number and age there may be extended warranty on the parts, check with Jenn Air to be sure

Apr 24, 2010 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

I had an F1 Code on my Jenn Air WW2780B Double Wall Oven, and turned both ovens on to heat up, which they did, and the F1 code never came back after that... so far. Could it be fixed?


Hi, This code is an indication of a fault that exist within the actual relay board. It is malfunctioning at this time, and should be replaced asap, if possible.This relay board is located inside the unit, mounted on the cooling fan shroud. Once replaced, the F1 code will be cleared automatically.

Relay board part number: Y04100261

Click here to view an exploded diagram of the cooling fan shroud, with relay board attached. The relay board is labeled number 9, and the shroud is labeled number 1

Oct 27, 2009 | Ovens

1 Answer

Beeping and displaying F1. Press stop and 30 seconds later it starts again.


too high temp F1 fault code its either the keypad, or the control board.if the thermostat or oven sensor is bad,it could have got the keypad or control board too hot, and caused the F1

Aug 30, 2009 | Jenn-Air 30 in. Pro-Style Electric Single...

2 Answers

Jenn-air w156, displays f1 fault code. how do i


This is a Defective touch pad or membrane

Replace touch pad or membrane (this problem is usually the touch pad)

Jun 17, 2009 | Jenn-Air 27 in. Electric Single Wall Oven...

1 Answer

Jenn-Air Wall Oven Model #WW30430P F5 Fault Code


I have the exact same problem with an F5 fault code. I also have a new clock assembly. RepairClinic.com said "Jenn Air fault code F5 = Hardware and watchdog circuits disagree / Replace clock assembly (also called the ERC)

Jenn Air Fault code for newer models F5 = Power to element relays disabled in cook mode
1. Intermittent oven temperature sensor or wire harness or,
2. Intermittent contact on power relay board"
This doesn't help since it is too technical. What should I do next?

Oct 19, 2008 | Jenn-Air WW30430P Stainless Steel Electric...

1 Answer

My older jenn air double wall oven


shooter, F1 is usually the touchpad failure. You can try disconnecting the touchpad ribbon from the control and cleaning the ends with an eraser. See if the F1 stops. Catriver.

May 24, 2007 | Jenn-Air JJW8230D Electric Double Oven

Not finding what you are looking for?
Jenn-Air JGW8130DD Gas Single Oven Logo

501 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jenn-Air Ovens Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Jenn-Air Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...