Question about Cisco SG200-26 24 10/100/1000 Ports, Gigabit Ethernet Smart Switch, 2 Combo Mini-GBIC Ports

1 Answer

Default password for a Cisco SG200-26? cisco, cisco do not work .. ??

I pressed the red button to return to factory defaults, but the credentials of: cisco (user) and cisco (password) are not accepted. Admin left, trying to get access..Please help .

Posted by on

  • Don Dean Oct 27, 2012

    Resolved - Default IP was used by another device. Found it with DHCP tablelookup and default passwords worked

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same issue after what I thought was a succesful reset. It turns out I hadn't reset the switch completely. There is a reset pin hole next to the power switch. Hold it in with a paper clip for at least 30 seconds. ( I was holding in the power button for 30 seconds.)Then you can use the cisco admin and cisco for password defaults. Hope this helps someone in the future since I spent WAY TOO MUCH TIME on it :)

Posted on Jan 17, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: what is the default enable

The default user name and password for Cisco routers and switches is usually:
user name: Cisco password: Cisco
Make sure to capitalize the C's.

Posted on Mar 17, 2011

technical114
  • 1851 Answers

SOURCE: Hi, what's a password on the router Cisco Catalyst

Try using username (none) pass public/private/secret or
cisco - cisco, ADMIN - changeme, pixadmin - pixadmin, root - attack, superuser - superuser as username - password. These are the defaults credintials for the Cisco routers.

Stelios.

Posted on Feb 22, 2010

zutil
  • 16 Answers

SOURCE: catalyst ws-c2926 password recovery problem

  1. Attach a terminal or PC with terminal emulation to the console port of the switch. Use the following terminal settings:
    9600 baud rate
    No parity
    8 data bits
    No stop bit

  2. Unplug the power cable.
  3. Hold down the mode button while reconnecting the power cord to the switch. You can release the mode button a second or two after the LED above port 1x is no longer illuminated.
    The following instructions appear:
    The system has been interrupted prior to initializing the flash file system.
    The following commands will initialize the flash file system, and finish loading
    the operating system software:

    flash_init
    load_helper
    boot
  4. Type flash_init.
  5. Type load_helper.
  6. Type dir flash:. The switch file system is displayed:
    Directory of flash:
    2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-h-mz-112.8-SA
    4 drwx 3776 Mar 01 1993 01:23:24 html
    66 -rwx 130 Jan 01 1970 00:01:19 env_vars
    68 -rwx 1296 Mar 01 1993 06:55:51 config.text
    1728000 bytes total (456704 bytes free)
  7. Type rename flash:config.text flash:config.old to rename the configuration file. This file contains the password definition.
  8. Type boot to boot the system.
  9. Enter N at the prompt to start the Setup program, Continue with the configuration dialog? [yes/no] : N
  10. At the switch prompt type en to turn on enable mode.
  11. Type rename flash:config.old flash:config.text to rename the configuration file with its original name.
  12. Copy the configuration file into memory: Switch# copy flash:config.text system:running-config
    Source filename [config.text]? (press Return)
    Destination filename [running-config]? (press Return)
    The configuration file is now reloaded.
  13. Change the password: switch#configure terminal
    switch(config)#enable password Cisco
    switch#control/Z
  14. Write the running configuration to the configuration file:
    switch(config)#write memory

Posted on Feb 09, 2009

ward_knutson
  • 64 Answers

SOURCE: default pasword

Cisco switches dont have a default password.
You will have to perform a password recovery process that is quite extensive.
You need to console into the switch using hyperterminal or teraterm and follow these instructions located at: http://www.cisco.com/en/US/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

Posted on Dec 20, 2008

  • 19 Answers

SOURCE: How to reset the cisco switch to factory default?

When you say you were able to connect to the switch through hyperterm, were you able to login with the enable password? If not, you cannot reset the factory defaults without the enable password. If you do not have this then search on Cisco's site for password recovery for your model switch. If you did login with the enable password, the command to run for CATos is "clear config all". For Cisco IOS, you have the right command with "write erase". When you issue that command, do you get a "Erase of nvram: complete " or an error? Are you issuing the "reload" command after a successful erase? Be sure you answer No when it asks "System configuration has been modified. Save? [yes/no]:" as sometimes this seems misleading and some people think they mean to save the reloaded default. They are really warning you that you are about to loose the old configuration and attempting to prevent you from accidently erasing it. So answer "no". After a successful reload of the IOS you should also clear any VLAN information. To do this, issue "delete flash:vlan.dat" and then do another "reload".

Posted on Aug 29, 2007

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How i reset to factory defaults without passwords?


That depends upon the brand of the router. It would be wise to google for the particular brand.

There often are software means to perform a reset but here are the hardware means.

For Netgear:

  1. Press and hold the Wireless On/Off and WPS buttons until the Power LED blinks red (about 6 seconds).
  2. Release the Wireless On/Off and WPS buttons and wait for the router to reboot.
For Linksys:

1. Press the red reset button on the back.
2. Unplug it from power for 30 seconds. Plug the power back in.

For Belkin:

1. Find the reset button (depends on the model).
2. Depress the reset button for 15 seconds.
3. Wait one minute for the router to restart.

Here is a tutorial for Cisco routers:

http://www.networkworld.com/article/2343961/cisco-subnet/how-to-reset-a-cisco-router-to-factory-default--removing-the-startup-configuration-file.html

Here is one for TP-Link:

http://www.tp-link.us/article/?faqid=496

For D-Link:

Push a paperclip into the hole marked reset on the back and keep it depressed for 10 seconds.

The default user name is usually admin and there is no password (password is blank).

May 11, 2015 | Computers & Internet

1 Answer

I ofrget my router password


MOST, if not all, cisco routers have a small recessed button to reset the router to Factory defaults. If you've lost your password, you can hold that button for 30 seconds to reset ALL router settings to factory default. MOST Cisco/Linksys routers use admin/admin for the factory default id/password.

Jul 07, 2014 | Computers & Internet

1 Answer

Linskys e1000 reset and password


Hello from here you can download a manual:

http://homesupport.cisco.com/en-us/support/routers/E1000

You need to install Cisco Connect software.
To reset it you have to press a small button at the back of the router
With power on.

E1000 Default Password & Other Default Login Data Version Default Username Default Password Default IP Privileges All [none] admin 192.168.1.1 Administrator
Good luck

Oct 29, 2012 | Cisco Linksys Wireless N Home Router...

1 Answer

Account name for linksys router


The factory default log in credentials consist of an empty or blank Username, and "admin" (no quotes) for the Password.

It is not possible to determine the Username / Password combination if it has been lost or forgotten. The router will need to be reset to factory defaults in order to gain access to the internal setup pages of the router. This is often done by pressing and holding the reset button on the router for about 30 full seconds. The button is usually recessed to prevent accidental activation - and requires a narrow pointed device such as a pen tip or paper clip to depress it. You should find the button on the rear, near the power jack or antenna on many Linksys routers and on the newer LinkSys / Cisco types it is located in an identified recess on the bottom of the case.

Resetting will delete any settings that have previously been saved, and return the router settings to factory defaults. You should run "ipconfig /all" from a DOS command promt and print out the results to help you restore some of the settings of your network when changing from the router defaults. Good luck!

Jan 05, 2012 | Linksys Wireless-G WRT54G Router

3 Answers

How to change admin username & password on cisco 2911 router


agree that turn off your modem first before trying to open the router's setup page. By default, there's no username and the password is admin on Cisco 2911

http://www.3anetwork.com/cisco-cisco2911/k9-price_p238.html

Nov 04, 2011 | Cisco 2911 Router

1 Answer

I forgot to change the default public credential User: cisco and pwd: cisco. Un fortunately I did restart the router. I would like your assistance to gain access to the router or to reset it back to...


Here is a cisco page that goes over the password recovery procedure. Once you reset the credentials, you can make any configuration changes needed. You will also have the option to keep the existing configuration in place but change the password, if the configuration has any use to you.

http://www.cisco.com/en/US/products/sw/iosswrel/ps1831/products_tech_note09186a00801746e6.shtml

Mar 11, 2011 | Cisco (1841) Router (cisco1841)

2 Answers

I lost, or dont remember, the password to my Cisco router


Hello,
routers have a way to be reset when this happens. It is usually done by pressing a button on it for a few seconds. This kind of button usually needs to be pressed by a pen tip or unfolded paper clip. Once the reset process is completed, your router will either have no password assign for th default administrator account or have it reset to a default which is mentioned in your router configuration, usually "admin".
If you provide us with the exact model number of your router, which can be found on the router itself, we can provide you with the exact location or the reset button and what will be the credentials to log in after the reset.
Regards,

Jan 23, 2011 | Cisco Computers & Internet

1 Answer

Reset cisco airnet 1130ag


There are 2 ways to reset the access point.

Using the MODE Button

Follow these steps to delete the current configuration and return all access point settings to the factory defaults by using the MODE button:

1. blank.gifOpen the access point cover

2. blank.gifDisconnect power from the access point (the power jack for external power or the Ethernet cable for in-line power).

3. blank.gifPress and hold the MODE button while you reconnect power to the access point.

4. blank.gifContinue pressing the MODE button until the Ethernet LED turns amber. (approximately 2 to 3 seconds). Then release the button.

5. blank.gifAfter the access point reboots, you must reconfigure it using the web browser interface, the Telnet interface, or the access point console port.
Using the Web Browser Interface

Follow these steps to delete the current configuration and return all access point settings to factory defaults using the web browser interface:

1. blank.gifOpen your Internet browser. You must use Microsoft Explorer (version 5.x or later) or Netscape Navigator (version 4.x or later).

2. blank.gifEnter the access point IP address in the browser address line, and press Enter. An Enter Network Password screen appears.

3. blank.gifEnter the username Cisco in the User Name field.

4. blank.gifEnter the password Cisco in the Password field and press Enter. The Summary Status page appears.

5. blank.gifClick System Software. The System Software screen appears.

6. blank.gifClick System Configuration. The System Configuration screen appears.

7. blank.gifClick the Reset to Defaults button.

Note blank.gifIf the access point is configured with a static IP address, the IP address does not change.

8. blank.gifAfter the access point reboots, you must reconfigure it.

Aug 13, 2010 | Cisco Aironet 1131AG 802.11a, 802.11g/b...

Not finding what you are looking for?
Cisco SG200-26 24 10/100/1000 Ports, Gigabit Ethernet Smart Switch, 2 Combo Mini-GBIC Ports Logo

6,376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Prashant M
Prashant M

Level 3 Expert

2260 Answers

brian soufane

Level 3 Expert

693 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...