Question about Radware LinkProof Application (904627-cl3) Networking Switch

2 Answers

I need to know how to configure link proof radware

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi Nalinfrancis,

One way you can config the LP is to log on to the serial interface and then configure an IP address to the first eth port that is available. Then connect directly to the port using a crossover cable depending on the laptop or pc that you use if it can switch put your laptop/pc on the same network that you configured on the port. Then connect via your browser to the IP address assigned to the LP. Logging with you default username and password. From there you can do all the configuration via the web interface.

Regards,

Andrevz

Posted on Apr 16, 2009

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Hi, Can anyone tell me the troubleshooting steps for High CPU issues in Radware Linkproof devices...

Regards
Rajesh P

Posted on Jul 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO CONFIGURE D-LINK DES1024D TO CONNECT TO INTERNET


You can also configure it with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then click on WAN settings set it as your internet service provider settings enable DHCP Then click on wireless and enable it. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Jun 01, 2011 | D-Link DES-108 8-Port Ethernet Switch

1 Answer

I need the master password


If the switch has not been configured leave the username and password blank here is link to dlink support which has the manual and everything you need to know to configure and reset it.

Apr 30, 2011 | D-Link Dlink DES-3028P Switch 24-port...

1 Answer

Trunking problems


  1. u may need to check first internal network broad casting. if any system is giving too much packeting
  2. connectors of cables which is properly crimp
  3. quality of cable
  4. cable which is comes in ur premises through area junk box is properly connected.
  5. u may need to check load balancing of network from your authorised vendor

Apr 06, 2009 | Cisco Catalyst 2950SX-48-SI 48-Port...

1 Answer

I need to change my routers MTU settings


enter configuration (default ip @ is 192.168.

Access your router’s configuration http://192.168.0.1 (this is default)

user and password (dafault admin/ and blank nothing)

Then go to the WAN option select on the lower part the MTU value.

it's 1500

try a lower value 1482 for example, 1480...


hope it helps

feed back plz


Apr 02, 2009 | D-Link DES-1008D 8-Port Ethernet Switch...

1 Answer

Dlink switch


Lenesh,
What are you trying to do? Switches don't need configuring as much as routers and modems. Tell me more about what you are trying to do.
Thanks
Kevin

May 22, 2008 | D-Link Computers & Internet

Not finding what you are looking for?
Radware LinkProof Application (904627-cl3) Networking Switch Logo

Related Topics:

1,480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Radware Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

98762 Answers

David Payne
David Payne

Level 3 Expert

14037 Answers

Are you a Radware Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...