Question about Troy-Bilt Pony Garden Tiller

1 Answer

Econo-horse tillerser.#e023842 need new oil seals on tine shaft

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 430 Answers

You can order them from your local MTD dealer.

Posted on Nov 05, 2012

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: troy bilt horse pto clutch will not disengage

The problem is lack of lubrication in the pto coupling. Losen the two swing bolts carefuly,block the front under the motor. Separate the tine transmision from the housing and grease both sides with as much grease as you can work in. Work the lever as you do this. Should fix the problem.

Posted on Feb 14, 2009

landsend
  • 1066 Answers

SOURCE: leaks oil around the tines.

 an new oil seal needs to be put onto the output shaft of the transmission.  remove the plug wire if you attempt to pry out the old seal and tap in the new seal.  Be careful not to damage the case and grease the seal and shaft when you replace the oil seal 

Posted on Mar 29, 2009

  • 26 Answers

SOURCE: troy-bilt horse engiine runs good , tines work,

The wheel shaft on a Horse tiller is one piece so if the shaft turns on one side it will turn on the other. make sure the pin that holds the wheel on is not missing that would let it spin on the shaft.
That's the only thing I can think of that would cause that problem. Hope that helps.

Frank

Posted on Oct 07, 2010

  • 26 Answers

SOURCE: When the clutch is disengaged the tines still turn.

If you email me at fbarnes@mfa-inc.com I have a couple of Econo-Horse manuals that I downloaded that I can email to you. They don't really have a clutch just belts and pulleys so its probably just needing a new belt or a belt tension adjustment. I have a Econo-Horse tiller and it is a nice machine I think mine is about the same age as yours.

Good Luck,

Frank

Posted on Oct 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Leaking tine shaft


your seal on the shaft defective,
www.ask.com/mfg.name/make/model/service/parts/leaking/tine/shaft/

Oct 02, 2015 | Troy-Bilt Troybilt Horse 6, 7 And 8 Hp...

1 Answer

The rear tine seals are leaking ive taken the bolts out but the tines will not come off what can i do


You could try putting the tiller to use, preferably where it will have to work hard to till the ground it unsuccessful you may need a torch and some good old fashion luck to loosen tines from shaft. Now consider this; if the bearings are worn so that the shaft is loose new seals will not hold up and you will risk doing further damage to the worm gear located on rear shaft and possibly other damage to your transmission from contaminated oil.

Mar 04, 2011 | Troy-Bilt Pony Garden Tiller

1 Answer

The oil seal where the tiller attachment fastens to the tiller is leaking how do i remove the seal


IF THIS IS A WALK BEHIND TILLER OR FRONT TINE TILLER. THERE SHOULD BE PINS OR BOLTS HOLDING THE TINES ON THE DRIVE SHAFT REMOVE THESE AND PULL THE TINES OFF THE TILLER. THEY MAY GIVE YOU A HARD TIME GETTING THEM OFF SO DON'T GIVE UP. ONCE YOU GET THE TINES OFF YOU SHOULD SEE THE SEALS YOU CAN POP THE OLD ONES OUT WITH A SCREW DRIVER CLEAN OUT THE SOCKETS WHERE THE NEW SEALS WILL GO REPLACE THE NEW SEALS GENTLY WITH A SMALL HAMMER TAPPING THEM IN EVENLY AND TRY NOT TO BEND THE SEAL

Feb 05, 2011 | Garden

1 Answer

I have a 5 hp troybilt pony tiller. The axle seals need replacing can you describe the best way to replace them. This tiller was built in Feb. of 1990.


http://www.mtdparts.com/webapp/wcs/stores/servlet/OperatorManualView?storeId=10101&catalogId=19502&langId=-1

Go to this website and type in PONY for your model number and find your operator manual by your serial number. The operator manual should have detailed instructions on how to replace your seals.
On the Horse model you remove the wheels and then carefully use a couple of screw drivers to pry out the old seals being careful not to scratch the wheel shaft sealing area. Then polish the wheel shaft with fine emery cloth to remove any sharp edges. Then grease the wheel shafts and carefully slide the new wheel seals on and use a piece of plastic PVC pipe cut square that will slide over the shaft and gently drive the seal to the depth the old seals were installed at. You dont even have to drain the gear oil. Getting the wheels off the wheel shaft is sometimes a problem if they are rusted on. if you can get the wheels off its not to hard to change the seals.

Frank

Sep 13, 2010 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

When the clutch is disengaged the tines still turn.


If you email me at fbarnes@mfa-inc.com I have a couple of Econo-Horse manuals that I downloaded that I can email to you. They don't really have a clutch just belts and pulleys so its probably just needing a new belt or a belt tension adjustment. I have a Econo-Horse tiller and it is a nice machine I think mine is about the same age as yours.

Good Luck,

Frank

Jul 08, 2010 | Troy-Bilt Pony Garden Tiller

1 Answer

PTO making noise when engaged in forward drive


It's 90 weight gear oil but most likely the output shaft seal has been gone for a consdierable amount of time and has leaked out and is just now making noise, they don't normally make noise right away after the oil runs out. put oil up to the plug fill hole and watch if it runs out the shaft seal if it does then it will have ti be repaiered.

Nov 13, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

Replace tine shaft oil seals - Junior model


on my pony the disc came off when i removed all of my tine shafts. then i pulled the old seals out an drove the new ones in

Apr 27, 2009 | Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0...

1 Answer

Leaks oil around the tines.


 an new oil seal needs to be put onto the output shaft of the transmission.  remove the plug wire if you attempt to pry out the old seal and tap in the new seal.  Be careful not to damage the case and grease the seal and shaft when you replace the oil seal 

Mar 29, 2009 | Troy-Bilt Garden

1 Answer

How to remove rear tines to replace seals ?


The tines sometimes get frozen to the shaft. You might try penatrating oil and use a heat gun or hair dryer to heat to loosen.
Also tap wiht a hammer around shaft.

Mar 19, 2009 | Troy-Bilt Garden

3 Answers

Oil seal for rear tine shaft


The serial number is located on a flat spot just above the right wheel shaft where the gear housing and the top gear cover meet. It will be a six digit number stamped in the metal.

Frank

Mar 11, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

Not finding what you are looking for?
Troy-Bilt Pony Garden Tiller Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Troy-Bilt Garden Experts

Jay Finke
Jay Finke

Level 3 Expert

1338 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Troy-Bilt Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...