Question about Panasonic CT-36HL43 36" TV

2 Answers

PIP on old panasonic tv only shows the channel you are watching

I bought an 32 inch older (1999 it says on the back of the tv) panasonic and it has a great picture but the PIP only shows the channel you are watching! I didn't receive the original remote control but the one that came with the tv has a pip button and controls its functions. I would like to use the pip function to watch two programs at the same time, can you help me?

Posted by on

  • mlvisse Jan 19, 2009

    I have the exact same problem, same tv

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Determine your exact model - there should be a sticker on the back.
Similar to: CT32HX40B, CT32HC43G, CT32S20U, etc, etc.

Go to below link and download the appropriate PDF for your model.
(Tip: Set page to " Show All Rows" for ease of use.
http://service.us.panasonic.com/operman/findmanual.aspx?cat=DTV

Depending on your source input (Cable, Antenna, both) - the PIP instructions will vary.

Note: The PIP is not all it is cracked up to be anyway, so you may be wasting your time, also if you get the PIP in a stuck mode... See the link to fix it: http://www.fixya.com/support/t664989-turn_off_panasonic_pip


Posted on Jan 31, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 135 Answers

The model number please or if you go to the Panasonic website you can dowload an instruction manual.
SUPER8

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a panasonic model ct-27g14a tv from a thrift store when i got it home i found that the parental lock was activated and did'nt have the code.


Sorry,u must have it orignal codes,there noway to unlock secrect personal codes.U push the channels + or - buttons manual controls couples times.Might get in the tv input.Hook up,use it with DVD player can watch DVD Disc thought.Sorry, you probally only can watch shows rated Y for children only.

Jun 02, 2010 | Panasonic CT-27G14 27" TV

1 Answer

I have a old tv 36 inch panasonic ct-36d30 my tv


sound like yoke short problem. replace same yoke as possible . good luck!

Feb 15, 2010 | Panasonic CT-36D32 36" TV

1 Answer

Can't change our Panasonic TV channel to watch DVD input


Buy a 21 way scart.This will have an 'AV' enable connection built in. After fitting, turn on the TV, then turn on the DVD player. It will automatically enable the DVD through the scart socket.

Nov 10, 2008 | Panasonic CT-32SX31 32" TV

1 Answer

PIP change


you can change the channel of the small screen .just read the user manual of your tv.to your problem is only in the remote control

Oct 13, 2008 | Zenith Z32X31D 32" TV

1 Answer

Pip won't turn off


how did you explain the problem you have to reach the correct code
from remote to turn off or on of the pip circuit - i can suggest to
use the original remote control or somethig else delfo

Mar 21, 2008 | Panasonic CT-32G22 32" TV

2 Answers

Picture in picture problem


When you use the Time Warner Digital box, you're using the tuner inside that box rather than the tuner inside your TV to select a channel. Picture in picture TV's have two tuner's inside so you can view two channels, but they can only tune the analog channels from your cable company, and only if it's hooked up in a manner that will permit this to happen.

So you only have one digital tuner (the Time Warner Box) so you can only view one channel at a time even though your TV supports Picture in Picture.

It MAY be possible to have limited use of the PIP if you connect your TV in a different way. Your Time Warner box is most likely connected to your TV set with composite cables, those are the Yellow, Red, White cables. If you buy a coaxial cable splitter and split the cable before it goes into the Time Warner box you can then run a coax cable into both the Time Warner box and the coax input on your TV. This would allow you to tune the analog Time Warner channels with both of your TV's tuners. In my area I think the first 60 channels or so are still available in analog, but there is no way to watch any of the higher premium channels without the Time Warner box.

If you go through these steps and you select the coax input on your TV your PIP will work on the lower channels. It MAY be possible to tell your TV to display the input from the composite cables on one of the PIP screens and the input from the coax on the other, but I kind of doubt it.

I know this sounds complicated and if you're not familiar with the way all this works it is complicated. The reason lots of people won't respond to this kind of question on this site is because there is no easy fix and by trying to help I run the risk of getting a bad rating. I don't get paid for this, I just like trying to help, so if I have not explained this in a way that's helpful to you please ask some additional questions before you give me a bad rating. Thanks.

Jan 01, 2008 | Panasonic CT-32D31 32" TV

1 Answer

No sound on my 8year old panasonic tv.


It worked fine yesterday. Sound on all channels. Sometimes the picture goes black on channel 6. We can get it back by going up one channel, then back to 6. it is due to cable signal ie weak. now there is no sound this is due to sound section 1 loose connect in sound section 2 speaker 3 problem in sound section some part must have failed.

Sep 17, 2007 | Panasonic CT-32SX12 32" TV

1 Answer

Set up an a Panasonic TZ-20L3Z


Press MENU button, select PRESET and then , select MANUAL PROGRAM and SEARCH, when search completed the program stops. Give the channel and store.

Aug 19, 2007 | Toshiba 27A34 27" TV

1 Answer

Panasonic CT-36SL13 Can't select video inputs


On a Panasonic to do a factory reset while the set is on press in on the power and action buttons on the front of the TV at the same time. In a few seconds the screen shouls go blank and come up with a screen that says "CHK" in the upper left hand corner. Once it does that press the action button again to clear the screen. You have now reset the TV to factory settings and will have to re-program the channel memory once again. Hope that works...

Apr 23, 2007 | Panasonic CT-36SL13 32" TV

1 Answer

Grey screen, white lines


adjust your screen at the back of tv flyback down you see the fucos and screen adjust the sreen ok

Nov 06, 2006 | Panasonic CT-36G34 36" TV

Not finding what you are looking for?
Panasonic CT-36HL43 36" TV Logo

803 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68202 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Radames Pagan
Radames Pagan

Level 3 Expert

195 Answers

Are you a Panasonic Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...