Question about 791XV The 791XV is a 2-way Security and Remote Start system. Th

Open Question

I can't find the valet switch for my Viper 791xv. Where can I find it?

I recently bought a vehicle with the Viper 791xv installed. I can not find the valet button for it though. Can anyone help me find it? Not exactly sure what the button looks like. I know it is there because we recently had a remote programmed to it. I looked all over inside for a button of some kind, but I don't see anything anywhere. thanks for any help.

Posted by on

  • Charity Hill
    Charity Hill Dec 12, 2012

    found it! thanks everyone! it was in the console. had to have a tech show me.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 12 Answers

SOURCE: No install instructions

email me at face2face11@bellsouth.net and i will give them to you. i 've been doing install professionally for 10 yrs and have access to directechs (DEI technician website)

Posted on Jan 22, 2009

  • 899 Answers

SOURCE: viper remote stopped working 791xv

I have the same remote and it comes disconnected in the battery section from the battery hitting it and then the commands and speaker stop working
as shown here
bf76e1a.jpg

Posted on Apr 05, 2009

  • 53 Answers

SOURCE: Viper 5701 remote programming

1st you need to enter the remote into progamming Hold the Function button until the remote gives a long beep and LED light comes on the remote a (it takes about 8 sec.) Then press and hold the remote start buttom until the remote beeps 3 times and LED lights up. Now your ready to program the remote

One of the door has to be open . Insert the key - turn the key to the On position then press the button on the antenna once and then press it again and hold it

You hear a chirp and then you press the lock button on the remote and then you hear a second chirp to recieve confirmation and then release the button and the turn off the key .

Remote should be program

Posted on Jul 12, 2009

  • 1 Answer

SOURCE: My Viper 791xv remote isn't receiving the page

My battery ran low and I jump started my car which some how caused the problem. My viper technician made me a buy new remote but the problem continued even with the new remote.
Try disconnecting the battery of your car for ten minutes and then reconnecting it. It worked for me. Now i have a extra remote which i don't need.

Posted on Jan 19, 2010

  • 132 Answers

SOURCE: how to program viper 5701 remote

Unlock doors
Push and hold f button for 8-10 seconds until amber light is on solid
Push Remote start button for about 4 seconds till amber light flashes 3 times
Put key in to IGN position
Push valet (black button) one time and release
Push and hold valet button
Push either lock or unlock on viper remote
Key out of IGN
Test unit
The horn or siren may sound afterwards to indicate SUCCESS!!!!!!

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where the **** is the Viper valet button?


Consider how the switch will be used before choosing a mounting location. Check for rear clearance before drilling a 9/32-inch hole and mounting the switch.The GRAY wire in the two-pin plug may also be used as a (+) ghost switch input and can be connected to any (+) switch in the vehicle. (See Feature Descriptions section of this guide.)

This is from the installation manual for the Viper 300. To answer your question, it is probably camoflaged. They only needed to tie +12vdc to the input line. What does this mean? Well, my best guess is, they are using one of your switches on your dash to act as the Valet function. Look for where the Gray wire, from the wiring harness of the Viper goes to: that WILL BE your hidden Valet switch. Best of luck!

Viper 300 ESP Installation Manual Plug in Harnesses Super Bright Led Valet...

Feb 15, 2016 | Remote Start System

1 Answer

I had to replace the battery in my car and now my remote will not do anything lock or unlock the doors start the vehicle or pop the trunk what do i do?


Reprogram the remote: turn ignition on, press and release valet switch one time. Press and hold valet switch. While holding valet switch, press lock button on remote. The alarm should chirp to confirm entry into the programming mode (when you press and hold the valet button) and when you press the lock button. Turn ignition off. Test remote.

Jan 24, 2011 | 791XV The 791XV is a 2-way Security and...

4 Answers

My Viper 791xv remote isn't receiving the page information from the unit in the car. When I press the unlock, lock, or remote start button, it works, but then the remote beeps as if it didn't work (3 sets...


My battery ran low and I jump started my car which some how caused the problem. My viper technician made me a buy new remote but the problem continued even with the new remote.
Try disconnecting the battery of your car for ten minutes and then reconnecting it. It worked for me. Now i have a extra remote which i don't need.

Oct 12, 2009 | 791XV The 791XV is a 2-way Security and...

1 Answer

Led light stays on


if you are finished with the install, then it's in valet mode. if you are still working on the alarm it's on because the alarm needs a ground.

May 20, 2009 | 791XV The 791XV is a 2-way Security and...

2 Answers

Car is completely locked down


Let's hopethat the installer actually put in the valet switch for the Viper! Lcate the valet switch. ALWAYS put mine down by the e-brake lever under dash. (I assume that the alarm is going off? If not, go to next step.

Find the alarm/start brain under dash. Unplug main 6 pin 12 gauge wire harness. Wait 5 minutes, then re-appy the power plug. Alarm "may" go off, then try again.

Hit me back if you need further assstance. TTYL

Larry T
Winona Lake, IN

Jan 28, 2009 | 791XV The 791XV is a 2-way Security and...

1 Answer

Viper remote starter


Sounds like the tach connection has been loosened or slipped out of position. Here is a link for installation manuals, Will help in location and inspection of tach wire.
http://www.directeddealers.com/manuals/ig/viper/N5501V_12-06post.pdf

Jan 17, 2009 | 791XV The 791XV is a 2-way Security and...

2 Answers

No install instructions


email me at face2face11@bellsouth.net and i will give them to you. i 've been doing install professionally for 10 yrs and have access to directechs (DEI technician website)

Dec 31, 2008 | 791XV The 791XV is a 2-way Security and...

1 Answer

Driver's door won't unlock with remote


This may be a problem with wiring. I will need to know what the make and model is of the car. Also keyless entry system stock OEM or was that an option you have added? Lastly, did you install this system or was this installed by a cetified DEI corperation?

Thank you,
Luis

Dec 02, 2008 | 791XV The 791XV is a 2-way Security and...

Not finding what you are looking for?
791XV The  791XV is a 2-way Security and Remote Start system. Th Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Viper Vehicle Parts & Accessories Experts

Tre Elkins

Level 3 Expert

643 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Joseph Gallucci

Level 2 Expert

120 Answers

Are you a Viper Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...