Question about Washing Machines

Open Question

Kenmore washer mod 110.28002010 stopped working with 9 minutes left in the cycle

Stopped with 9 minutes left in cycle. Lid locks and unlocks, can set for new cycle, sensing mechanism comes on. But nothing. I'm not sure, but I may have heard a very, very faint motor niose this morning.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 91 Answers

SOURCE: Kenmore Elite HE4t Washer Control lock lit, door locked

121 MINUTES USUALLY DRAIN CYCLE PLZ REMOVE 3 BOTTOM PANEL SCREWS 7 MM SCREWS, TO OPEN DOOR SLIDE RIGHT HAND TOWARDS DOOR LOCK ,THERE WILL BE A SMALL LEVER TOO PULL DOWN ,NOW ITS OPEN,,, SINCE U HAVE BOTTOM PANEL OFF PUMP IS RIGHT IN FRONT REMOVE PLASTIC HOUSING CLOCKWISE ,,,REMEMEBER HOLD 3 GALLONS OF WATER STILL ,HAVE BUCKET READY ,NOW CLEAN OUT PUMP AND DEBRIS ,, CLOSE IT UP SHOULD BE FINE NO MORE PROBLEMS ,,,,,

Posted on Jan 02, 2009

Ad
  • 7 Answers

SOURCE: the lid is locked on my kenmore oasis washer

Unplug the washer first. How to open the service lid. Latches are approx 4" in from corners in front (where the little crack is below the lid) insert a putty knife, pushing in on the latches and pull up as it gives. Hold onto the side you've released and pop the oter side and lift up.
Now you will be able to see the lid lock; center front from underneath. Use a 1/4" nutdriver and remove the latch.
Now as far as I know, pn:8563937 was replaced with: W10059230 Bought mine from www.midwestapplianceparts.com.
Install is simple; 3 screws (1/4") behind the back panel will allow you to access the plug. Just feed the old one out and the new one in.

Posted on Aug 03, 2010

blueextc3221
  • 15935 Answers

SOURCE: Kenmore Elite cloths washer Mod.#

It appears your lid switch/door latch has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 30, 2010

TheMobilian
  • 8220 Answers

SOURCE: We have a kenmore HE

What ya could do is remove the 3 screws on the service panel.
themobilian_2951.jpg

Posted on Sep 03, 2011

TheMobilian
  • 8220 Answers

SOURCE: Wash cycle stopped with 3 minutes left. Door is

You can open the door using the rip cord that is located under the service panel. While yall are in there open the filter and see if something is in there screwing up the works.
themobilian_2954.jpg

More here

Posted on Sep 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Washer stopped working in the middle of the cycle, did not drain completely and now will not finish cycle


http://www.partselect.com/Repair/Washer/Will-Not-Start

Sears PartsDirect

the Sears Pars Direct YouTube Videos are at the link above.

Water Filters Lawn Garden Appliance Parts
For questions or assistance, call
1-800-252-1698
M-F 6:30 a.m. - 10:30 p.m. CT
Sat 7:00 a.m. - 9:30 p.m. CT
Sun 7:30 a.m. - 9:30 p.m. CT
Great Site and great help.

Jun 06, 2015 | Kenmore Washing Machines

2 Answers

Kenmore washer model #21302 lock on light is flashing, will not start


Kenmore top load washer 21302, the sensor light is on and the lid lock light is on with a clicking noise. What could be wrong with it and how do I fix it?

May 21, 2012 | Kenmore Washing Machines

1 Answer

Wash cycle stopped with 3 minutes left. Door is locked and we can't unlock it. What should we do?


You can open the door using the rip cord that is located under the service panel. While yall are in there open the filter and see if something is in there screwing up the works.
themobilian_2954.jpg

More here

Sep 03, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

My Kenmore Elite He washer is only 4 years old, it's motherboard has already been replaced about 2 years ago and now it powers on you set a cycle and the lid does not lock. Push stop (like to add clothes)...


faulty lid switch I have had to work on a couple of these inside the machine there should be a technicans sheet so that you can do a diagostic test of the machine which will give you an error code dont be surprised with this unit if when you fix one thing that it gives you another code. I think the last one i worked on i had to replace motor harness lid switch and main control board before it stopped giving me error codes hope this helps

May 01, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

Lid lock not on, and machine is not going through


On this washer, the dl code indicates a failed lid lock mechanism. Pressing pause/cancel should reset the controls.

You may have to unplug the unit for 20-30 minutes, then restore the power.

If that doesn't work, the only other solution would be to replace the door lock assembly.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Nov 17, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 80 series mod 110225842400 stopped working during cycle. Tub won't drain and will not agitate.


Hi, When the washer is in spin or wash cyles, do you here any motor noises? It sounds like the lid switch might be bad. Sometimes you can actually see if the lid switch is broke or not. Please let me know if The lid switch appears to be the problem or if I can assist you further.

Vic

Jun 20, 2009 | Kenmore 20172 Top Load Washer

2 Answers

Code ul appears shortly after start up


I think ul is unbalanced load, not unlocked lid.

Jul 21, 2008 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Kenmore washer just stopped


Open and close lid, listen for 'clicking' sound. If no 'clicking' sound, check/replace lid switch. Also try tightening the lid hinge screws on the left side. if these screws come loose, the machine will not operate

Jun 14, 2008 | Kenmore 24642 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Brad Brown

Level 3 Expert

15950 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...