Question about Canon imagePROGRAF iPF5000 InkJet Printer

2 Answers

White lines appear in print from ipf5000

Suddenly I am getting a series of white lines in the middle of my prints on glossy paper

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 79 Answers

Try to print a nozzle check
then print in photoshop boxes in Cyan,Magenta,Yellow,Reb,Green,Blue. See in witch colors is the mismatch.
As i can imagine there must be a mismatch in the flat cable that transmit the data from the main PCB to the carriage relay assy.
The second effect must be the carriage relay assy board

Posted on Mar 30, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 8,637 Answers

Normal 0 I suggest you get a sheet of Card Stock (Heavy paper) and place it in the feed way. Then press the print button applying a slight amount of pressure on the Card Stock so it will feed through the printer. The reason for this is in some cases I have been able to clear the paper track of debris that was deposited there over time.
Worth a try, as I have fixed a number of printers this way, saving costly repairs.
Hope this helps. Bud

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I get rid of lines on photos


Sir/Madam

Step one: Retry the print

If printing on glossy paper was paused or interrupted in the middle of the print job (for instance, if a cartridge was replaced), the resulting print may show a grainy band. In this case, retry the print and avoid interrupting the job.

Step two: Free up system resources and ensure direct communication

The PC can cause the printer to pause if it is not fast enough to keep the printer fed with data. The following steps can help alleviate this problem.
  1. Make sure that the PC meets the minimum system requirements for this printer.
  2. Restart the PC.
  3. Close out of all programs except for the program the print out will originate from.
  4. Shut down programs running in the Task Bar by right clicking on them and choosing exit. These programs will restart the next time the PC is rebooted.
  5. Ensure that the USB cable is 10 feet in length or less. Make sure the USB cable goes directly from the printer to the PC with no intervening devices in between such as a USB hub.

Step three: Check the paper or specialty printing material


  • Make sure the media is not damaged, scratched, or curled. Always store printing materials in a sealed plastic bag, especially in a humid environment, to help protect the material from damage or curl.
  • HP inks and media are designed to deliver optimum results. Other media may not perform as well.

Step four: Increase the print quality mode

If reprinting did not help and the paper or specialty printing material is not damaged, check the print quality mode:
  1. Open the Printer Properties dialog box.
  2. On the File menu in your software program, click Print .
  3. Make sure your printer is selected.
  4. Click the button that opens the Properties dialog box. Depending on your software program, this button might be called Properties , Options , Printer Setup , or Printer .
  5. Click the Features tab.
  6. In the Print Quality drop down list, choose a higher print quality (for instance, if the print quality is Fast Draft or Normal , switch to Best or Maximum DPI ).

Step five: Clean the printheads using the printer control panel

If you still see streaks or lines in your printouts, clean the printheads using the printer control panel.


NOTE:Always allow the printhead cleaning routine to complete. If the printer loses power in the middle of a cleaning, make sure to repeat the cleaning and allow the printer to complete it.
  1. Press Menu on the printer control panel. Figure 3: Menu button on the printer control panel

75b681b9-ee6e-426d-8740-fa0d2e25518c.gif

  1. Using the arrow keys to move through the menu options, find and select Clean printheads , and then press OK .
  2. Following the directions on the printer screen, load paper so the printer can print a test page after cleaning the printheads. Use plain paper to conserve photo paper.
  3. Press OK to begin cleaning the printheads. A Print Quality Diagnostic page prints at the end of the cleaning. Figure 4: Print Quality Diagnostic page

4e6ad9ee-965d-4875-a411-60df245be32f.gif

  1. If there are white lines across any of the color blocks on the Print Quality Diagnostic page, press Cancel to repeat the cleaning.
  2. Cleaning may be repeated a number of times. The number of cleanings (and therefore the length of the procedure and the amount of ink and paper used) will vary depending on the severity of the problem. A Print Quality Diagnostic page is printed after each cleaning. Look for white lines through the blocks after each cleaning, and if the print quality seems to be getting better (fewer white lines), continue to repeat the cleaning. Eventually, a Recommend Six-Minute Cleaningmessage will appear on the printer display. If the print quality has been improving, press OK to perform six-minute cleaning.
    • As soon as the white lines no longer appear in the color blocks, the problem should be solved. Print a normal print job to confirm that the print quality is acceptable.
    • If the print quality is still bad after the six-minute cleaning, or does not improve with repeated cleaning, or is not acceptable even though there are no white lines through the color blocks, go on to the next step.

      Step six: Align and calibrate the printheads

      If you still see streaks or lines in your printouts, align and calibrate the printheads.
      1. Align the printheads:
        1. Load plain, white, unused paper in the main tray.
        2. Press Menu on the printer control panel. Figure 5: Menu button on the printer control panel

675f657f-f99c-4893-b194-f33663f3ec77.gif

    1. Select Calibrate Printer , and then press OK .
    2. Select Align Printheads , and then press OK .
  1. Reset the closed loop calibration:
    1. Press Menu on the printer control panel.
    2. Select Calibrate printer , and then press OK .
    3. Select Reset closed loop calibration , and then press OK .
    4. The printer LCD will display Ready .
  2. Color calibrate the printer using closed loop calibration.
    1. Load HP Advanced Glossy Photo Paper in the main tray.
NOTE:Only HP Advanced Glossy Photo Paper should be used for this process. If plain paper is detected by the printer, the calibration procedure may fail or print quality may be affected.

    1. Press Menu on the printer control panel.
    2. Select Calibrate Printer, and then press OK.
    3. Select Closed Loop Calibration, and then press OK.

Step seven: Clean the printheads manually

If you still see streaks or lines in your printouts, clean the printheads manually:
  1. Gather the following items to clean the nozzles on the printheads:
    • Distilled water (tap water might contain contaminants that could damage the printheads)
    • Cotton swabs or other soft, lint-free material that will not stick to the printhead
    • Sheets of paper or paper towels to rest the printheads on
  2. Open the top door of the printer.
  3. Press and hold OK until the printhead assembly moves to the left side of the printer and stops.
  4. Raise the printhead assembly cover.
  5. Remove a printhead and place it on a piece of paper with the ink nozzle plate facing up.
    Figure 6: Removing a printhead


30d99a41-4c4a-4257-8d32-275b6505dcad.gif

NOTE:Do not touch the ink nozzle plate with your fingers. Touching the ink nozzle plate will result in clogs, ink failure, and bad electrical connections.

NOTE:Do not leave the printhead outside the printer for more than 30 minutes. Ink nozzles exposed to the air longer than this might dry out and cause printing problems.

  1. Lightly moisten a cotton swab with distilled water and squeeze any excess water from the swab by pressing it against a clean plastic or tile surface. Do not use your fingers to squeeze the excess water from the swab, because the oil from your fingers could contaminate the swab.
  2. Gently wipe the nozzles on the printhead with the cotton swab. Figure 7: Wiping the nozzles

6ad22fec-fdff-448d-8e80-3acdfb93d75c.gif

  1. Wipe until no ink residue or dust appears on a clean swab.
  2. Insert the printhead in the printer.
  3. Repeat the steps above for each printhead. When all the printheads have been cleaned and reinstalled, close the top door of the printer.
    note.png
    NOTE:If a message appears on the printer screen directing you to replace a printhead, click the Contact HP link on this page to contact HP support.

Step eight: Replace the printhead

If you still see streaks or lines in your printouts after performing all the steps above, one or more printheads may need to be replaced. If your printheads are still under warranty, click Contact HPon this page to arrange to replace the printheads.

I Hope Your HP Printer Problem Is Solved By Now,In case You still Having HP Printer Problem,Then I suggest You Visit Below URL Link:

http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00725354

Or

If You still Need assistants Then Follow Us On:


HP Printer Support

Feb 13, 2014 | HP PSC 1209 All-in-One InkJet Printer

1 Answer

My hp printer casts purple to black and white prints


Tried your settings with no luck. Also tried every canon profile listed to no avail.

These are my settings:
Color management:
Color handling: Photoshop manages colors
Source space: sRGB...2.1
Printer profile: Canon MP620 Series GL2/52G
Rendering: Perpectual

Media Type: Glossy Photo paper
Print quality: standard
Effects: borderless

Printer Preferences:
Color Intensity: manual-set-everything is 0-matching:none


I am using Kodak glossy paper and I am using that setting. I am printing a digital scrapbook page with color. I used black and white pictures in the page trying to get rid of the purple trees, so it shouldn't be printing any color at all in the photos, but the limbs are still purple.

Under color settings in PSE I have checked "optimize for printing".

I am off to the store to pick up another package of photo paper..maybe HP or Epson will be better (I think those are the other 2 choices in the store)

Will check back in after I try the other papers

Aftermarket car headlights

Jun 11, 2012 | Printers & Copiers

1 Answer

Using glossy paper but lines appear


try and clean the rollers by running system checks on the printer software or you may be running out of ink, try replacing your cartridges

Jul 20, 2009 | HP Printers & Copiers

1 Answer

ESP5 printer not printing photo's on glossy paper


Hi there,
  • Unplug the printer cable from the computer.
  • Unistall the printer drivers from Device manager and also unistall the all the printer appications
  • restart the computer
  • try to download drivers from the website
  • after installing drivers and software it will ask you to connect the printer.
  • then you can connect the printer and and try to Print the test page.
Hope this help. Please Rate My Response! Thanks!
PREM

May 18, 2009 | Printers & Copiers

1 Answer

A series (10) vertical lines on print outs


See Charge roller my be dirty or Catriges PCU Units

Jan 22, 2009 | Ricoh CL3000E Laser Printer

2 Answers

Just want to print black !


hallow ,,,if your lookin to just print black and white so .while printing ,go the printing properties or prefrencies ,,in the colour option click just use black and white

Jan 10, 2009 | Printers & Copiers

1 Answer

Canon i9900 black ink smudging


ok, What cartridges are you using, Are the Canon cartridges?
What paper are you using, is it Canon paper?

If you are to both of these it could be wise ordering a printhead, but this is mostly caused in the uk by None Canon Paper.

Please let me know what you are using?

Sep 24, 2008 | Canon i9900 InkJet Photo Printer

1 Answer

Black smugs on any glossy print


check the fusing area. (where the paper is heated)there is an adjustment for envelop . set it to normal because the pressure on fixing unit is too loose.

Jul 11, 2008 | HP Color LaserJet 2600n Printer

1 Answer

Re: Smudging


Try Cleaning the printheads. you usually have a utilitie to do this in :- Printer preferences. Also try several Print test Pages. It appears that your getting a surge of ink, at the initial printing stage. use standard paper to do all tests with. 1:- it,s cheaper. 2:- it,ll help soak-up any surplus ink. whereas the glossy paper does,nt soak it up too well. If these solutions don,t help. check HPs site for fault diagnosing and repairing.
Hope this helps you in the right direction.
Mike@Compurepair.

Feb 20, 2008 | HP Deskjet 6980 InkJet Photo Printer

Not finding what you are looking for?
Canon imagePROGRAF  iPF5000 InkJet Printer Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts

kakima

Level 3 Expert

96372 Answers

old marine
old marine

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...